RB191PLV Amana Refrigerator - Instructions

Removed motor in freezer replaced it with new motor

The replacement ice maker was exactly the same size and model. All the mounting screws lined up and install was snap. The website parts description was very good and helpful. We now have ice cubes with no over flowing glacier in the ice tray.

Pulled the fridge out, Took bottom panel off. Removed 3 screws holding motor. Unplugged connector, cut wires, attached old connector on new motor. put blade on new motor.installed in fridge, put cover back on.

Followed the utube video demonstration. There was no instructions for changing the relay and overload and so this part was not used.

The kit I recieved was perfect. All parts fit and where a perfect match. I will give you an A+ in handling my order and shocked by speed of your delivery.

tried installing the gasket on the unit. after fighting that for awhile, I removed the freezer door. after that, things went a little better. if your not mechanicly inclined.... I would advise you have it done by a service man.

Unlike what the online video showed, my bottom freezer French door refrigerator didn't use hooks to secure the icemaker in place. Instead, it used three tabs with screws to secure it in place. I could see two of them, but not the third one. After removing two screws and realizing that the icemaker was still pretty well secured, I felt around and found the third screw (at the top, right behind the front of the icemaker). Once I got that out, the replacement went easily, as shown on the video. That third screw was a little challenging to put back, but after a few tries I got it in. The icemaker is now making ice like a champ! Good work PartSelect! And the part came quickly, as advertised.

First pulled the Ice tray out of the freezer, Pulled the cord for the power to the refrig. Removed 3-Srews with the nut driver and disconnected the Power Supply to the Ice maker. Removed it from the freezer and started to remove the Bail and install the bail in the new Ice maker. Remove the cover from the side of the old ice maker and install it on the new ice maker. Put it back in the Refrig and connected the power cord and installed the 3-screws and reinstalled the Ice Tray and 30 mins. later it started making ice. Thanks for the Youtube Video it helped a lot to take the pressure off of doing it your self.

Unscrewed the right control knob. Removed the left temperature control knob (there is no screw holding it), removed one screw to rear of small panel then pried open from the rear of the small panel, there are two plastic tabs in front of the small panel holding it in place. Unscrewed the failed control unit and replaced it with the new one. Replaced the small panel and screw then the left side control knob, making sure of the alignment in the "off" position as the knob has to be pressured into a clamp arrangement on the cold control thermostat. Re-screwed the right knob into place, as well.

Move refrigerated and turn off water and unplug elect. Remove ice Ben and guide on right side. Move one screw on the bottom and lousen tow screws on top. Remove ice maker to unhook electrical connection. Transfer parts from old one to the new one . Revise the removal of it and when done .Plug in cord and turn on water. If you have done everything very carefully you will have ice in a few hours.Good luck.

Replaced the ice maker. I have a 3 door refrig. It has a bottom drawer freezer. Remove the freezer door to make this much simpler. On my unit, the ice maker is installed with three screws, rather than one and two clips. Check before you try to pull it out. You should unplug the old ice maker from the refrig, leaving the wires on the old ice maker. It's much easier to remove the old wiring harness from the old ice maker once you've removed the front plastic cover on the unit. Both plugs on the harness have clips on them to prevent accidental disconnections. Be sure to find and press the clip releases before you pull on the wires. Nut driver makes this job easier than screw driver. You only need one size for all screws. I used the old ice maker bottom mounting clip rather than trying to bend the new one to shape. Much easier. My old ice maker had an extra wiring clip, which I moved to the new unit before the install. There is one wiring clip to hold the temperature probe, and another just to keep the wires neat. Letting the old ice maker front plastic cover warm up a bit before you try to pry it off for reuse is a good idea. Less chance of cracking. Two hours after the install, I had new ice in the ice bin.

Your video was very helpful and accurate. However, my freezer is a bottom drawer type, so I needed to remove the freezer door first. There were 4 nutscrews which needed to be loosened, and door lifted off. Now with the door off, and both baskets removed, access to the ice maker was easy like your video. Also, the freezer compartment was much more accessible for cleaning as well. In 2 days after replacing the ice maker, we have had 2 full batches of ice, with full sized cubes! Your ecommerce shopping, delivery, and instructional videos made for a great on line buying and installation experience. Note: The Dacor ice maker was replaced with a Whirlpool ice maker part. Your replacement part was identical in all respects to the original equipment even though Dacor was not included in your list of compatible brands.

watched the video you have on installation and followed it with ease. The only part you need a tool is to loosen the first nut and then everything else pretty much pops out and you reinstall with the new part. The icemaker worked within an hour and makes perfect cubes. The videos are super helpful.

Followed your video instructions and tips. Real easy

Getting the old ice maker out was not difficult - it sits on a small ridge built into the freezer and then it takes three screws to attach it to the side of the refrigerator. Three important things to remember: (1) take off the metal bar that shuts off the ice maker from the old part, the new part doesn't come with the bar; (2) keep the screws and the cap from the old ice maker as they don't come with the replacement part either; and (3) make sure you put the water tube back into the holder otherwise it will pour all over the freezer (and not into the ice tray).