RAX7245AW0 Roper Washer - Instructions

watched a video that showed how to repair that you had on your web site. also read some of the remarks that other people left on site, one was super easy. just laid washer on its back, unhooked both water lines from pump. unhooked both metal clips holding pump and pulled off. replaced new pump in reverse order. didn't have to go thru all the procedures of taking off the body or nothing. 15min job.

Replaced suspension, leveling and tub springs.

I followed the 'how to' video, stopping the video when needed to complete a portion of the repair. I was doing the repair in a laundry closet, which took me a little longer, but with the right parts ordered and the instruction video this project was easy and does not take very long.

Took agitator apart as shown in video, changed the agitator dogs, put agitator back together. Works great.

The washer breaks down slightly different than shown in the video. Install of the new part went pretty well. It was reinstalling the washer cover that caused most of the grief. You have to have all of that sheet metal lined up just right or it won't go back together. All good now...very happy.

The replacement part was "perfect" and the parts dept. lady I spoke with, was professional in description and correctly fitting part. The part arrived, we popped off the other where it would have fit, then the "collar" below it, put on the new collar, the dial and we were done. Before that, we'd been using a pair of pliers to move the dial around to do the laundry. This was an easy experience, quick upon arrival and we we're pleased with the purchase and how nice it is to have a working appliance again.

I followed the helpful video from PartSelect. Removal and Replacement of the Clutch Assembly was fairly easy. Just make sure you have enough towels to dry up any water that may come out after tipping the washing machine over. After Replacement the washing machine works like new. Thanks PartSelect.

Looked on line and found the cheapest repair for my symptoms seemed to be the tub wear pads. Disconnected the washer, tilted it to where I could inspect the pads and discovered one was missing. So ordered a set, (Only complaint was the shipping was as much as the part). Parts arrived in 2 Days (!). Tilted the washing machine again...reached up with a small flathead screw driver and pryed the old pads off...snapped the new ones on (takes a little pressure, so eat your wheeties)...and job done. Stood everything back up and re-connected hoses, drain and plug...Works like brand new...Unfortunately for the wife who thought she was going to get a new one....LOL

After entering the Parts Select website and searching for the model number information, I found a video which described the problem. The video explained the step by step procedure to access the possible problem. The problem was exactly as the video described, I ordered the repair part, made the repair, and placed the washer back in service. Oh, by the way, the part was delivered to my house the next day.

The spin cycle was super slow leaving clothes soaking wet at the end of a full wash cycle. Ordered a clutch repair kit, watched the how to video that was e-mailed to me with my order while I did the repair and got it done in about 45 minutes. This was my first true appliance repair outside of maybe a busted fuse or replacing the heating element in a stove. Never thought taking the motor, transmission and clutch out of the washer and putting all back together would be so very simple. Meanwhile my wife is pissed because she thought she might be able to go get a brand spankin new washer...until I fixed the old one. Thanks for saving me some dough PartSelect.

I followed the instructions to remove the agitator and install new drive assymbley. This is the second time the drive unit has been replaced over the last 3 years. I have no idea how long the unit has been operating in this rent house. It was there when I bought the rental 10 years ago.

went to you tube and watched a video on how to take it apart and replace the clutch assembly.

replaced it with a new cold-hot valve and everything worked perfect.

After removing and inspecting the old part, I didn't see any visible sediment buildup that would have impeded the flow of water through the valve. The problem may have been a partially burned out solenoid or just simple wear that prevented the valve from opening all the way. So I decided to replace the part. The only thing that prevented this from being a 10-minute installation was the fact that I didn't have access to the side of the machine, so it was a little awkward leaning over from the front with the cabinet tipped forward to bolt the new part on through the back. Also, I found it difficult to connect the outlet house clamp to the part once I had it on, so I had to remove it, connect the hose to the loose part, and then re-bolt the part on with the hose already connected. Still and all, a simple fix, and the washer fills very quickly now.

Remove protective cover and inner seal with gasket from top of agitator. Use socket set with extension to reach bolt in bottom of agitator and loosen bolt. Remove assembly from washer. Take out interior disk and remove broken agitator directional cogs. Replace with new directional cogs. Reassemble parts in reverse order. Easy Peasy,took about 5 minutes.