RA720K1CT Hotpoint Range - Instructions

After watching the video and ordering the parts and searching for the right size socket (which took most of the time) and finding medical tape as I had no electrical tape I took of the back unhooked the terminals and following the wires to determine which ones needed to be replaced I followed the video instructions on reverse as my son had spliced new terminal blocks into the old wires I taped each new wire to the one it was replacing and pulled it through the back of the stove and into the front attached the new wires to the new block and pushed the clips on the other end of the wires to the knob boxes. I rolled up the excess wire and taped it securely with medical tape so it wouldn't unravel and be in the way when I reattached the back shield on the stove. After I repeated the process for the second terminal (I had two that kept shorting out) I reassembled the stove plugged it back into the wall and used both burners that night to cook dinner! I have had no problems with those burners since then. Really if you watch the video first and follow the instructions you should have no problems. It is really quite simple if someone hasn't tried to repair the problems without replacing the wires. Splicing new blocks into old wires just doesn't work. If I have this problem again, which I hope I don't, I will be confident in my ability to fix the problem myself. Thank you parts select for repair video and the parts.

took out a couple of screws and replaced with new switch, plugged in switch wires. very easy

I UNPLUGGED THE WIRE, ASSEMBLE THE BURNER ELEMENT KITS
LIFTED UP THE SURFACE BURNER PANEL,
OPENED THE BACK RANGE COVER,
UNSCREW THE NUT HOLDING THE BURNER CONNECTOR, DISCONNECT THE REPLACEMENT WIRES ON THE BACK PANEL
TRACE THE NEW WIRES CLIPS TO THE BACK PANEL & TIGHTEN THEM WITH EXISTING NUTS
SCREW THE OTHER ENDS BACK WITH NUT HOLDING THE BURNER CONNECTOR

I turned the power off at the circuit breaker, pulled the stove out from the wall, and removed the plug. I removed the top back panel, and took the burner switch out by unscrewing the 2 screws in the front of the panel. I used pliers to remove the wires one at a time from the bad switch and put them on the good switch. I replaced the new burner switch on the front panel and also, replaced the back panel. I put the plug back in the socket, pushed the stove against the wall, and turned the power on at the circuit breaker.

standard procedure, very simple

It took my son very little time to install control switch. Using a screw driver he removed the back panel directly behind burner units & replaced the control switch. Very easy.

Took back off and replaced.

simply replaced them.

The longest part of the job was finding my misplaced nut driver!!Note:A small socket set will do.Unplug stove from outlet,remove rear cover panel,lift stove top up to access terminal. remove the one screw that holds the terminal and slide off the two wire clips that hold the wires up out of the way.next clip off the old terminal leaving the old wires so you can tape the new wires on just to pull them through the hole.Once you have the new wires pulled up to the heat control unplug old and replace with the new,tighten the screw on the new terminal and don't forget to slide on the wire clips

Top front sloping sheet metal panel with all controls and plastic end caps has to come off. Need 2 people, one to hold it while other replaces switch. Problem was getting screw holes on bottom ends lined up and cuts from sheet metal edges. Ten minutes to get it apart, 40 to get it back together. New switch works fine.

Pull range away from back wall. Remove panel behind control knobs by removing the screws that hold it on. Find hot burner light that holds lens. Remove broken part of lens. Insert new lens into hole on front of control panel and into hot burner light receptacle. Replace back panel. Slide range back into place.

Only used a phillips screwdriver.

Since we got the stove,this is the second time we've repaired these connectors. The first time the connectors came with pre-stripped wires, wire nuts and heat shrink tubing. This set came with pre-attached spade terminals, so I had to crimp the mate to the wires in the stove then put heat shrink tubing on the splices. I also had to bend the part of the connector that mounts onto the stovetop. These had a horizontal tab for the mounting screw rather than the vertical design that our ranges uses. If the connectors designed for the earlier model were available, it would simplify installation since shrink wrap and wire wraps came in that kit and the mounting bracket would fit correctly.

Removed two screws holding the housing in place and loosened two more on the back it order to free it. Switch was held i place with two screws, removed those. Transfered wires one by one on the new switch, which was identical OEM part, and replaced the screws. VERY simple.

First I removed the burners and pulled the stove out to get the back cover off. Removed the back cover after main power was shut off. Removed old burner terminal blocks and replaced with new ones. Replaced back cover and pushed stove back into place. Turned on main power to stove checked burners and they worked. DO NOT REPLACE OR DO ANY ELECTRICAL WORK ON ANY MAJOR APPLIANCE WITH OUT FIRST TURNING OFF THE MAIN POWER SOURCE.