Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Washer ran fine but woudl not drain water - low humming noise
Drain all the water out of the tub with a shop vac Remove rear drain hose and drained rest of water into a bucket Remove small rear panel (bottom left hand corner) where the drain hose connects Tipped washer up about 45 degrees to get underneath it - Supported it with a few paint cans Remove internal drain hose/clamps from pump - w/ pliers Remove belt cover (gray plastic) with socket - 3 bolts Remove wire assembly plug from socket Remove old drain pump with socket - 3 bolts Install new drain pump - 3 bolts - plug wire assembly into socket Reinstall belt cover - 3 bolts Reinstall hose to drain pump (note panel will be inside washer) Feed drain hose panel through hole and reinstall - 1 nut Re attached drain hose to exterior drain plug You are done !
Very simple to repair. Be sure to drain the tub outside or into the sump pump then lay the washer on its side. The pump is right there on the bottom of the basket with 3 bolts. You will also need to remove the belt cover to get to the plug. So simple and saves you hundreds off repair man prices.
Water was dripping into the detergent tray when the unit was off.
Removed the control panel back plate cover. Removed the 3 screws that held the water control valve in place. I then unplugged each solenoid one at a time and plugged it into the new control valve. Once all wires were transferred, I pulled the old valve up and put the new valve on. Then reinstalled the screws that held it down and reinstalled the cover plate. Very simple job !
Water flowed into the washer all the time, even if unplugged
I removed the back panel at he top of the washer, then remover the two screws that hold the top control panel in place. Then I removed the three screws that held the water valve in place. I removed the valve from the water ports and then disconnected the four electrical connectors. I plugged in the new valve and plugged the valve back into the water ports. Reinstalled the screws, control panel and the back panel. Very easy repair, anyone could do it!
At the end of the wash cycle, the clothes were still wet
I unplugged the machine from the power source and removed the drain hose from the back and allowed any remaining water to drain out of the machine. I then tipped the machine back so that I could work underneath it and secured it in that position. I removed the old drain pump assembly by first disconnecting it from the outflow hose, then removing the three bolts which held the motor housing cover on and disconnecting it from the power source. This part was the the most difficult and time-consuming as the wires are plugged in very tightly but once those were separated, it was just a matter of unscrewing the drain pump assembly from where it was anchored to the underside of the washing machine. I simply reversed those steps to install the new one and it was in place within 10 minutes. Set the washing machine down in the correct position, reconnected the drain hose, and plug the machine in. I did reset the fault codes by using the manual found taped to the underside of the machine, but this was very simple to do and only took a few minutes. I’m not sure if it was necessary to do that step at the machine works perfectly now. I am a woman and found this repair very easy to do.
Put washer on it side. Removed shield belt and pulley from motor. Unplugged and unsnapped speed sensor and replaced with new one . Washer spinning like it should. Problem solved
Would not pump water out.water filled and lid would lock, when put on drain and spin cycle, would just get a low humming sound.
Dipped water out as much as possible,tited washer at a 45 degree angle and propped it up. Took the 3 bolts out holding the pump assembly and the 3 bolts holding the belt guard.Unplug wire connecter,pull out assembly and than pull drain hose off of assembly. Reinstall the same as you take apart. Was a easy fix, and worked as it should.
Wash machine would not drain/pump water out of machine.
1 Disconnect power 2) Cut water supply to washer 3) Disconnect water supply hoses from supply. ***if pump broke with water in tub, remove water from tub. 4) tip machine onto it's front side 5) remove hose clamp of exhaust hose & then remove exhaust hose from pump 6) Remove pump with socket/ratchet 7) disconnect pump electrical plug 8) tell old pump to take a hike & throw in garbage 9)Iinstall new pump 10) Do steps 7—1 in reverse order to put back into business.******Be prepared to do it again in 6 months; I havnt had good luck!
Being a woman I had to figure out tipping it in its front. I put it on a dollie and drop it down real easy. Removed all water lines after water was shut off. Removed bolts. Removed bolts on plate to the right to unplug old pump. Plugged in new one and replaced all bolts, hoses and tipped her back up. Works like a charm and I saved $408 by doing it myself!!!!!
The washer did not drain. It also did not click or sound like the drain cycle was being engaged.
Emptied the washer, took the back cover off, tipped it foward, unplugge the old pump, remove two mount bolts. The replaced the new pump. The new pump resolved the issue.