Models
>
PTW600BSR0WS
PTW600BSR0WS General Electric Washer - Overview
Sections of the PTW600BSR0WS
[Viewing 5 of 5]
Keep searches simple, eg. "belt" or "pump".
Pump Drain Assembly
PartSelect #: PS12723115
Manufacturer #: WH23X28418
This drain pump assembly is for washers. Drain pump assembly removes water from the washer during the drain portion of the cycle. The assembly may include multiple parts; refer to your parts diagram f...
$48.21
In Stock
DRIVE BELT
PartSelect #: PS11736832
Manufacturer #: WH01X24180
This drive belt is sourced from the original manufacturer for use in various models of dryers. It is a rubber belt that connects the motor to the transmission of the washer. It enables the drum to spi...
$14.60
In Stock
CLUTCH
PartSelect #: PS11729473
Manufacturer #: WH05X24185
This is a clutch for your washing machine. The clutch is made of a white plastic material and is used within washing machines to engage and disengage the transmission during the wash and spin cycles, ...
$8.54
On Order
MODE SHIFTER
PartSelect #: PS16554752
Manufacturer #: WH03X30517
This is a mode shifter or shift actuator for models of washing machine. Mode shifters are designed to change the function of the washing machine motor, between spinning cycles and agitation, and is us...
$39.40
In Stock
Water Inlet Valve Assembly
PartSelect #: PS12171559
Manufacturer #: WH13X26637
This is an inlet valve for models of compatible washing machines. Inlet valves are electrically controlled solenoid valves that open and close as needed during the washing cycle, to allow water into t...
$58.74
In Stock
SPEED SENSOR
PartSelect #: PS16619248
Manufacturer #: WH03X32158
This is a speed sensor for a variety of washing machine models. Speed sensors are used to monitor the speed of the washer drum and communicate it to the electronic control board to slow or quicken it....
$11.71
In Stock
Anti-Siphon Clip
PartSelect #: PS271098
Manufacturer #: WH1X2725
This part helps prevent the backflow of water from the tub to main water line.
$12.55
In Stock
Questions And Answers for PTW600BSR0WS
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Donya
February 21, 2024
It’s like my control panel is locked up. Start pump flashing
For model number PTW600BSR0WS
Hi Donya,
Thank you for your question. If the start pump light is flashing, there may be an issue with the pump motor and you will need to check it for continuity with a multimeter. Set the multimeter to the Rx1 setting. Touch the pump’s terminals with the probes. You are testing for continuity and should receive a reading of zero or nearly zero. Next, you should test the ground connection by touching one of the probes to the bare metal housing while leaving one on a terminal. This test should not produce any reading. If the results of your tests are different from the above, you will need a replacement pump. We hope this helps!
Was this helpful?
Thank you for voting!
Related Parts:
Pump Drain Assembly
$48.21
In Stock
- < Prev
- 1
- Next >
Common Symptoms of the PTW600BSR0WS
[Viewing 7 of 7]Will not drain
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Will not agitate
Fixed by
these parts
these parts
Show All
Spinning Issues
Fixed by
these parts
these parts
Show All
Noisy and Marks Left on Clothes
Fixed by
these parts
these parts
Show All
Spins slowly
Fixed by
these parts
these parts
Show All
Draining Issues
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Washer ran fine but woudl not drain water - low humming noise
Drain all the water out of the tub with a shop vac
Remove rear drain hose and drained rest of water into a bucket
Remove small rear panel (bottom left hand corner) where the drain hose connects
Tipped washer up about 45 degrees to get underneath it - Supported it with a few paint cans
Remove internal drain hose/clamps ... Read more from pump - w/ pliers
Remove belt cover (gray plastic) with socket - 3 bolts
Remove wire assembly plug from socket
Remove old drain pump with socket - 3 bolts
Install new drain pump - 3 bolts - plug wire assembly into socket
Reinstall belt cover - 3 bolts
Reinstall hose to drain pump (note panel will be inside washer)
Feed drain hose panel through hole and reinstall - 1 nut
Re attached drain hose to exterior drain plug
You are done !
Remove rear drain hose and drained rest of water into a bucket
Remove small rear panel (bottom left hand corner) where the drain hose connects
Tipped washer up about 45 degrees to get underneath it - Supported it with a few paint cans
Remove internal drain hose/clamps ... Read more from pump - w/ pliers
Remove belt cover (gray plastic) with socket - 3 bolts
Remove wire assembly plug from socket
Remove old drain pump with socket - 3 bolts
Install new drain pump - 3 bolts - plug wire assembly into socket
Reinstall belt cover - 3 bolts
Reinstall hose to drain pump (note panel will be inside washer)
Feed drain hose panel through hole and reinstall - 1 nut
Re attached drain hose to exterior drain plug
You are done !
Read less
Parts Used:
-
Mike from NAPLES, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set
45 of 59 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Would not drain the water from the tub.
Very simple to repair. Be sure to drain the tub outside or into the sump pump then lay the washer on its side. The pump is right there on the bottom of the basket with 3 bolts. You will also need to remove the belt cover to get to the plug. So simple and saves you hundreds off repair man prices.
Parts Used:
-
Micheal from South Bend, IN
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
27 of 37 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer not spinning
Tilt washer back.
Remove belt gaurd.
Remove belt.
Remove pulley.
Remove clutch and shifter.
Install in reverse order
Remove belt gaurd.
Remove belt.
Remove pulley.
Remove clutch and shifter.
Install in reverse order
Parts Used:
-
Marvin from SHOSHONE, ID
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver
13 of 17 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!