Quick Question!

Have you ever purchased from PartSelect.com before?

Models > PDW9280N00SS > Instructions

PDW9280N00SS General Electric Dishwasher - Instructions

All installation instructions for PDW9280N00SS parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the PDW9280N00SS
31-45 of 306
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The mount for the pump was damaged in shipping. We remodeled our kitchen so we ordered the appliances befor we were ready to install them. They looked ok when got them but when we opened them the dishwasher was damaged. I tried to fix the problem but I couldn't get the vibration out.

  • Customer: CHARLES from BURTONSVILLE, MD
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 8 of 13 people found this instruction helpful
First thing I did was to turn off the water and electrial supply. Then take the side mount screws and remove the base cover disconect the water line slide out the washer. I then put a pad on the floor turn the washer face down on the pad. I disconected the drain line lossened the clamp on the pump. Then disconected the two wires and removed the pump.I then installed the new pump tightened the clamps reconected the two wires then conected the drain line. I then slide the washer back in place reconected the water line put the side mount screws in place. I then turned the water and electrial supplies back on. I then ran the washer to check for leaks. No leaks found iI then reinstalled the base plate. The vibration was gone after replaceing the pump. Thanks Charlie

The bottom rack had broken wheels and rusted prongs

  • Customer: MONICA from ENCINITAS, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 7 people found this instruction helpful
Exactly as described by a previous reviewer. I pulled out the old rack, put in the new rack and just moved over the cutlery rack.

Water Leaking

  • Customer: John from Lady Lake, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 7 of 11 people found this instruction helpful
First of all the part I ordered came a lot sooner than expected.
I thought it would take 5 to 10 days.
I ordered it on a Tuesday and it was at my door on Thursday.
The part was difficult to take off as this was the first time I attempted this.
When the new part came, I saw that I went to too much trouble to take the old one off.
It was installed in about 40 minutes and we were off and running.

Old basket rusted out, was falling apart

  • Customer: James from Davison, MI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 6 of 8 people found this instruction helpful
Took out old basket, took off the sprayer arm and put it on the new basket.. pulled out the old wheels on the side tracks and slid the new basket in...pretty simple...

White latch on soap dispenser broken- would not latch

  • Customer: David from Stamford, CT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 6 people found this instruction helpful
The first posted instruction is dead on (except there are 14 phillips screws (not 10) on inside of door. Also, when reconnecting the 2" quick connect, make sure it is fully inserted - otherwise the numbers on the display panel will not show correctly. Mine didn't the first time, and I had to re-open the door panel and giggle around with the connection to get the numbers to display properly.

Rusted upper rack with wheels

  • Customer: Herman from Winchester, MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 4 of 5 people found this instruction helpful
1. Removed the cap ends from the inner rails - easy

2. Removed the old rusted rack from the inner rails- easy

3. Removed the spray arm and conduit - a bit difficult: there's a hard-to-reach nut that you need to remove at the hub of the spray arm - A pain in the neck because it cannot be reached vertically.

4. Installed the spray arm and conduit onto new rack. Make sure the conduit aligns with the pipe at the rear inner wall! - easy

5. Installed the rack onto the rails - easy

6. inserted the cap ends - done!

Replaced dishwasher but had the wrong drain hose.

  • Customer: Victor from Phoenix, AZ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 5 people found this instruction helpful
Attached the drain hose to the dishwasher pump and to the sink pipes and I was done.

the dishes were not getting cleaned

  • Customer: James from Portsmouth, NH
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Wrench (Adjustable)
  • 11 of 26 people found this instruction helpful
I pulled out the racks and decided to take off the upper (mid) arm. It came off with an adjustable wrench. When I looked at the arm I could tell that some of the holes were blocked. Some debris had gotten lodged in the holes and were blocking the water flow. I used tweezers to remove the debris and it solved the problem. I then pulled out the lower arm and cleaned it with warm water. There were soap deposits and I wondered if other debris could be blocking this as well. Finally I went onto the web site and saw that for $40 including shipping I could replace these parts with brand new parts. I did and the machine washes like new again.

old part leaked

  • Customer: robert from east windsor, CT
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench (Adjustable)
  • 3 of 3 people found this instruction helpful
unscrewed dishwasher from cabinet, then I flipped dishwasher on it's side. loosen pump motor bracket arm on the end of the motor. loosen pump motor to pump conecter hose clamp and then unscrewed pump motor connector from dishwasher. To install I did the reverse. very easy.

Lost Rinse Aid cap

  • Customer: Jerome from Arlington, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 9 people found this instruction helpful
Inserted new cap purchased from PartSelect.

Water leak under Unit

  • Customer: GEORGE from LEVITTOWN, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 6 of 12 people found this instruction helpful
Remove Base Access Panel; Removed Valve Mounting Bracket & Valve; Disconnected Wire Connector; Disconnected Supply Line & distribution Hose; Reversed the Process. Piece of Cake; Part was O.E.M.Component Exact Fit; Took Longer to Write this than it took for Fix. Thanks I Will Be Back for other Parts.!

Wire basket rusting.

  • Customer: Scott from pleasanton, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 4 of 7 people found this instruction helpful
The Lower Rack was a simple swap. The Upper Rack had a tube and rotating sprayer that had to be removed and installed on the new rack. I used a nutdriver to remove a few screws and reinstall them on the new unit. Very simple.

Leak under the appliance

  • Customer: paul from arlington, MA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 3 of 5 people found this instruction helpful
After finding the leak source I have targeted the piece part on your web. It came 2 days after and I replaced the defective part by the new one. I switch off the water, untied the nut to release the pipe, take out the part.

The plastic wheels kept falling off the bottom rack of the dishwasher

  • Customer: Michelle from Spokane Valley, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 1 people found this instruction helpful
The old wheels and attachment brackets were easily removed since they were always falling off. I ordered all new brackets and wheels, but it turns out I didn't need new wheels. If your original wheels are in good condition, they are the same size as the new ones and fit the new brackets. The new attachment brackets are built differently than the ones that came with the dishwasher, but (a good thing considering the originals only lasted 1 1/2 years). The new brackets and wheels snapped together and snapped into place on the dishwasher in minutes--no tools were needed. It took longer to cut the parts out of the packaging than to install them. The bottom rack now rolls out like it did when it was brand new. Definitely worth the few dollars in parts.

Original wheels kept falling off, rack would go off track and it drove me crazy

  • Customer: Chris from Medina, MN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 1 people found this instruction helpful
Simple, took five minutes, no tools, problem solved.
All Instructions for the PDW9280N00SS
31-45 of 306