Models > NVL333EB0CC > Instructions

NVL333EB0CC Hotpoint Dryer - Instructions

All Instructions for the NVL333EB0CC
16 - 30 of 56
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dryer drum making a lot of noise
The felt liner between the drum and the front door was worn out. The plasitc glides were all torn apart. Clothes would catch in the rim of the dryer.

Anyways, just lift the lid and tilt the front of the dryer down (after unplugging the control panel). Although only the top of the felt was messed up, i replaced the whole thing. I used the paint stripper to take off the glue residue from the previous felt.

Once it was clean it was easy to glue the felt pieces in place, easy reassembly and the dryer is good as new.

The design of this dryer sucks. This is the 2nd time the felt was repaired. The first time cost well over $300.
Parts Used:
Lower Felt Seal Top Drum Glide Kit
  • Philip from Lake Forest Park, WA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer was squeeking for a while, and then eventually just quit working.
Took the top and the front panel off (took me a while to figure this out without breaking stuff). Took off belt, pulled out drum, replaced bearing, and then I also had to replace the ball (attached to rear of drum, which slides inside the bearing).
Parts Used:
Rear Bearing
  • Jesse from Battle Ground, WA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dryer would not start
My husband replaced the rotary start switch that we bought. However, the dryer still would not start. He then tested each remaining switch/dial (before we spent more money on parts) to see if the dryer would start if the electrical connection by-passed that part. None of the top panel switches was the culprit. Then he pulled the door switch. The dryer worked with the switch out, but still connected. He reset each wire, put the door switch back in place, and it failed again. He pulled the switch, added electrical tape to all the connections, and put it back. The dryer works fine now.
Parts Used:
Rotary Start Switch
  • Marie from Charlotte, NC
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
5 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Plastic shaft on switch broken.
On arrival at rental in Florida, knob & half of shaft are on top of the dryer. Thanks! It's fixed
Parts Used:
Rotary Start Switch
  • Harry from Bradenton, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
clothes were getting caught between front cover and drum . Tearing softer material and staining the other.
used a putty knife to press in the font clips removed top then front panel . pulled off the old felt and glids what was left of them. then used a 2'' air grinder with a 3m scuff pad to remove the old glue and remaining felt then glued the new ones back in place gave it about 30mins to set up then put it back together and works good as new
Parts Used:
Lower Felt Seal Top Drum Glide Kit
  • heath from winterville, NC
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers
5 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Two tips after you watch the videos (and video link)
Watch the videos for replacing the belt. The one by Kenmore is the most accurate even though it isn't GE -- the mechanisms are the same. Here is the link to the one I found most helpful: https://www.youtube.com/watch?v=G2wTmfurT5o

First: You don't need to pull the washer/dryer out at all. Leave it in place. You can put the belt around the drive shaft and get the tension pully in place by feel and inspect your work with a flasklight,

Second: There is absolutely no reason to spend $70 on a rubber belt. Other places sell it as cheaply as 10 dollars. Shop around -- the actual part is not at all impressive and should not be priced this high.
Parts Used:
Drum Belt
  • David from WASHINGTON, DC
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
load noise
took the top off, then the front,there 2 screws that hold the front on. there's a yellow thing on the front took that off, it is held on with one screw. on the back of the dryer on the bottom is a metal plate take that off, to get to the belt take that off. then there' 3 screws in the drum, take them off ,then you can slid the drum out. then take 2 screws off the bearing bracket, that's it. easy
Parts Used:
Rear Bearing DRYER BEARING BRACKET
  • jeff from coldwater, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Socket set
5 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer kept eating clothes! They'd catch between the door panel and drum.
*****I HIGHLY RECOMMEND buying both bottom felt and top felt with glides and replacing them as a pair. Do it now!!****

First I removed the screws on the top of the control panel and lifted the control panel free. Next I pried the top cover off the drier. Reaching down inside the drier, I removed 2 screws holding the front panel in place (one on each side of the drum, screw heads are INSIDE the appliance) Then the front panel popped off toward the front, leaving the drum dangling inside the cabinet. I removed the old top felt and glides one piece) which had nothing left to them. I used a rag soaked with Acetone and a putty knife to remove the old adhesive and clean the mating surface. Following the supplied instructions (that came with the part) I glued the new piece in place. I reassembled the dryer and tested it out - I recommend giving all internal air ducts a good vacuuming while the dryer is apart - and everything seemed OK for a week. Then another article of clothing fell prey to the dryer, becoming lodged between the drum and front panel again. I suspect the culprit is the space BELOW the drum where the bottom felt is worn much more than the brand new felt just installed. I HIGHLY RECOMMEND buying both bottom felt and top felt with glides and replacing them as a pair.
Parts Used:
Top Drum Glide Kit
  • Joshua from Bristol, RI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Clothes snagging and getting stained in dryer
Hardest part was getting the top off which ended up being quite easy, once I knew how. At the front of dryer, between the top and the cabinet, there are two spring clips that hold the top to the bottom. I could feel them with the putty knife but wasn't sure how to release them. Push on them with the blade of the stiff putty knife ... push hard and they will release. When the top was off I could see the screws that held the front. I unscrewed those, had easy access to the front glide that needed to be replaced. Pulled the old one off, followed the directions to glue the new one on, gave it about an hour to dry, reassembled and away we went. No more snagging.
Parts Used:
Top Drum Glide Kit
  • John from Granbury, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The control switch broke off flush from the start switch
My wife was attempting to start a load of laundry when the start knob came off in her hand. I figured the inside of the knob had broken loose and the stem from the rotary start switch would be sticking out, well the stem had broken off flush and the knob was fine. After ordering a replacement, I jerry rigged the broken one with a large screw driven into it and put it back in place, worked great, just had to put a screwdriver into the screw and turn it to get the dryer to start. I felt it was fine to stay that way but the wife insisted we install the new one to put the knob back in place. The new switch arrived very quickly and went into without a problem, just four screws to remove the panel, two wire connections and was working again.
Parts Used:
Rotary Start Switch
  • Jonathan from Chanhassen, MN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
there was no problem
installation exactly how your directions told me on the computer
Parts Used:
Rotary Start Switch
  • Edward from Garrison, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Switch was either stuck in start position or had to rotate full turn to start
Removed four allen head screws to expose inside of panel. Used flat blade screwdriver to raise spring retainer and turned switch counter clockwise to remove.
Parts Used:
Rotary Start Switch
  • DERALD from Burleson, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken start swithch from moving dryer
Removed top panel from dryer. Unplugged the 2 wires for swithch, rotated swith, and removed. Reversed the process. Put parts back together.
Parts Used:
Rotary Start Switch
  • David from Rice Lake, WI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken shaft in rear bearing
Take the top off and front off and disconnect the belt and lift the drum out and there it is . Easy and alot cheaper then new dryer and works like new .
Parts Used:
Rear Bearing Kit
  • frederick W from wall, NJ
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Wrench set
3 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rear bearing was broke
I like to fix , i have time and i just give me the chance to try , and i did it , i wish to pay less for the parts , but was a good feeling when the problem fixed
Parts Used:
Drum Belt Rear Bearing Shaft Support
  • Alonso from MONTGOMRY VLG, MD
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the NVL333EB0CC
16 - 30 of 56