Models > NJLR473ET0WB > Instructions

NJLR473ET0WB Hotpoint Dryer - Instructions

All installation instructions for NJLR473ET0WB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the NJLR473ET0WB
31-45 of 271
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The plastic door handle on the dryer broke and came off.

  • Customer: Jerry from Mindoro WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 6 people found this instruction helpful
I received the replacement part I ordered from PartSelect.com within 3 days of placing the order. I opened the plastic bag it came in. I snapped the part into the holes left vacant by aforementioned abscence of broken part.

Lint filter screen was broken

  • Customer: Katherine from Washaington DC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 6 people found this instruction helpful
Remove old one, put the new one in!

No Heat--dryer runs--Timer/Heat Selector does not advance

  • Customer: Jose from Dalzell SC
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 11 of 21 people found this instruction helpful
Ok so it finally died. Breakdown is relatively easy. UNPLUG the dryer before doing anything else. Remove the dryer vent plastic hose from the dryer--replace if torn. Remove the screws from the back plate covering the switches. Go to the front of the dryer--open door and locate 2 screws at about 11 and 12 o'clock. After removing these 2 screws you should be able to lift the top off the dryer. Take note of the wiring connections--I took a picture of the wiring from my cellphone just in case. Go behind the dryer and locate the access to the electric motor to remove the belt that spins the drum. There is a wheel/belt tensioner--remove the tension from the belt. You are now ready to lift the drum out. While you have this drum out, now is a good time to vacuum all the lint out. Once the drum is out, you'll see the heating element. If the wiring element is broke, just replace the wiring kit not the entire assemby (save $100). While you're at it replace the high limit and safety thermostats (about $28 for both) very easy to replace--unscrew and just replug the wires back to the original terminal locations. To replace the Timer/heat selector, remove a screw that holds the assembly and plug the wires back per your diagram or better if you took a picture from your cellphone. Assemble in reverse direction. Good luck!

broken dryer belt

  • Customer: alfred from copperas cove TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 7 of 10 people found this instruction helpful
First i removed the lower rear inspection plate to see what the problem was.
next i removed the screws in the front top panel.
next i lift the top back,the rear hinges held it in place.
next i removed the bolts that held the front panel in place,but before i removed the panel i removed the wires that were connected to the front elements and disconnected then,
next i removed the front panel,then i place the new dryer belt over the dryer drum,but first you have to rise the drum up a little to get the belt under it.
next i put all the front panels back in place,make sure you reconnect the wires that you removed earlier.
next i moved to the back panel, there i position the belt over the dryer drum,then i place the belt over the motor drive pulley, then i pull down the tension bar roller to the left and place the belt over it.Then i replace the rear panel in place.plug in the power core and turn it on. finished. After over 35 years this is the first time i had to replace the belt,matter of fact this is the first time i had to replace anything on this dryer, washers will that is a different story. but the dryer runs great maybe for another 30 +years LOL.

Dryer would not start

  • Customer: Robert from Santa Barbara CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 5 people found this instruction helpful
I checked the power (OK) and removed the four screws that held the timer/controls (upper panels) cover. This revealed a schematic for the dryer that enabled me to determine the door swich was probably the culprit. I pried out the old switch and, sure enough, it was always open (checked with multi-meter). I found the replacement switch easily using the dryer model number and "door switch" search string. Ordered Sunday night, the part came on Tuesday and took 2 minutes to install (no tools needed).

Intermittent starting gave way to no starting

  • Customer: Carl from Newburgh IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 8 people found this instruction helpful
a. researched internet to find how to access rotary starter switch
b. isolated all electrical input at breaker box
c. removed 4 torx screws on top of dryer head
d. lowered dryer head (swivels toward front)
e. pulled electrical connections from back of switch
f. turned and pulled thus releasing rotary switch
g. reversed procedure above
h. reconnected electrical
i. started dryer - it worked first time
j. watched football until wife came home
k. told wife dryer was fixed and what a bear it was to get it done :o)
l. that night accepted my reward for working so hard at fixing the dryer and saving us a bundle. :o)
m. now we are both smiling

My dryer was starting to throw a lot more heat than normal. I clean my lint filter every time I use the dryer. What I didn't realize was that over time, the lint filter had warped enough to allow lint to escape into the dryer and subsequently into the dryer vent system, clogging some areas almost

  • Customer: Nancy from Dalton PA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 5 of 5 people found this instruction helpful
I opened the vent system (screwdrivers to loosen screws) and used the shopvac hose and my hands to clean out what I could. I also snaked the shopvac hose down into the dryer and removed clogged lint. Then I just replaced the lint filter.

handle broken on dryer

  • Customer: Karen from Warwick NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 6 people found this instruction helpful
Removed the broken handle from the dryer and popped on the new one.

old bearing completley gone; shaft eating through race making a horrible noise when running

  • Customer: greg from abilene TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 4 of 4 people found this instruction helpful
pull top and front of dryer (6 screws), take belt off drum and pull drum out the front of dryer. Take the three star head screws out of stainless heat vent inside of drum and take old bearing housing out of back wall of dryer housing. Pretty much self evident putting everything back in, some trouble installing new bearing housing in back wall of dryer, screws are hard to turn in by hand (new hole). Vacum inside of dryer housing, install everything the way in came out, , plug it in and WA-LA.

extremely loud continous noise when drying laundry

  • Customer: wayne from waterloo NY
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set, Wrench(Adjustable)
  • 4 of 4 people found this instruction helpful
watched the video on your website,this made repair to the dryer very easy.hardest step in the repair was getting the belt hooked up on motor and tensioner,but being old and persistent i finally won!

Broken belt and worn bearing

  • Customer: Peter from Winter Haven FL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 4 of 4 people found this instruction helpful
Replacing the bearing and belt on a GE DDE6350BBL dryer

My belt broke and landed up in the bottom of the case, therefore no problem removing it.
Having to replace the belt I decided to renew the bearing at the same time.
Detailed instructions, with comments follow for those of you attempting this repair.
Most important, READ ALL THE INSTRUCTIONS BEFORE STARTING WORK
Take careful note as you take things apart of what they looked like before you started.

First unplug the appliance. Always unplug the appliance before doing any repair.
With the appliance stood in a space where it is accessible all round begin.
Open the front door and remove the small Phillips screws located at the top of the front panel.
( You have to look upwards to see them, normally four screws )
The cabinet top can now be lifted carefully upwards. It is a good idea to use a piece of
2 x 4 to hold this in a raised position for the time being.
Inside the cabinet on the right at the top, behind the door open switch, remove the two electrical slide connectors from the switch.
Remove the hex headed screws securing the bottom kicking plate, ( four screws )
Remove the two longer hex screws securing the bottom of the front panel, ( two screws )
Look inside the cabinet, each side towards the top there is one hex headed screw securing the top of the front panel to the sides ( two screws )
Hint head of screw faces back of cabinet.
The front panel can now be removed by lifting slightly up and away from the rest of the case. Do not try to move it too far, just turn it through ninety degrees and lean it against something heavy. Hopefully placed there to lean it on before you started.
Using a torx screw bit, remove the three torx screws securing the drum onto the bearing.
( A noise will be heard like something dropping, we will take care of this later.)
Lift the drum out of the case and set it aside.
Using a Phillips screwdriver remove the four screws securing the bearing to the casing.
Lift out the complete old bearing assembly.
Now is the time to thoroughly clean all the parts, before reassembly.
A Hoover with a crevice tool is good for removing most of the lint in and around the case. In severe cases it might be necessary to use a wire brush to loosen the lint.
Look in the bottom of the case and find the spacer, which fell off when you removed the drum. It is circular with a large hole in the centre and six holes around the side.
It is a good idea if you are adventurous, to remove the slide connectors for the heater elements and remove this assembly for cleaning. If you are not adventurous then cleaning it while installed is possible but be careful of the wire spirals, they are fragile

Helpful hint.
At this point take one of the old screws, which secured the bearing into the house.
Take this screw to a good hardware store and ask for two extra screws three inches long with the same thread. Make certain the thread is the same. Bring your new screws home, put them in a vice and saw off the heads, thus leaving two pieces of threaded rod three inches long of the correct thread. Doing this will save you a lot of aggravation later.

To replace the bearing, assemble the new bearing with a small quantity of high heat grease applied to the bearing surfaces. The old circlip can be reused without problem as long as it was not damaged when removing it.

Hint the new bearing is supplied with an 'o' ring in the groove where the circlip goes, this 'o' ring has to be removed before assembly.

If you have removed the heater assembly for cleaning it should be reinstalled now.
Install the new bearing in the casing using the four new screws provided.
Carefully screw your two threaded rods into two of the three holes in the bearing surface.
Locate the spacer plate onto the threaded rods and slide back until it is in the correct position.
Hint, it will only go on one way round, with all the holes lining up correctly.
Place the new belt loosely around the drum before it is installed in

blub burned out.

  • Customer: Mary from Oak Point TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 5 people found this instruction helpful
I first throwed the breaker then I took the old bulb out. Put new bulb in. Turned the breaker back on.
It worked great

Bearing was cracked and eating all my clothes

  • Customer: mavis from winnemucca NV
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 4 of 5 people found this instruction helpful
Boyfriend did the repair but it took very little time, the dryer now runs nice and quiet with no thudding and all my clothes are safe from being eaten!

Door wouldn't stay shut

  • Customer: Catherine from Windber PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 4 of 5 people found this instruction helpful
When I went home at Christmas, I saw that my Mom had been using a small bench to keep her dryer door shut. I wrote the make / model of the dryer down and found your website. I ordered the part, and my sister snapped it into place. My mom was so happy to have her dryer door stay shut again!

Door handle broken

  • Customer: Jennie from Louisville GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 3 people found this instruction helpful
Inserted handle into slots
All Instructions for the NJLR473ET0WB
31-45 of 271