Models > MZD2766GEB > Instructions

MZD2766GEB Maytag Refrigerator - Instructions

All installation instructions for MZD2766GEB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MZD2766GEB
16-30 of 833
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ice Maker was leaking water and causing the ice to freeze into a block

  • Customer: Shelley from Katy TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 28 of 28 people found this instruction helpful
First I removed the Ice bin, I then loosened the ice bin rail under the ice maker and removed the screw that attached the bottom of the ice maker to the side of the fridge. I unplugged the power to Ice Maker from the back of the fridge and unscreewed the two screws that secured the ice maker to the fridge. This allowed the Ice Maker to be removed from the fridge. To replace the new ice maker I simply repeated the steps in reverse.

while closing the door, the light switch fouled, resulting in the switch breaking

  • Customer: Kevin from Beckley WV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 28 of 33 people found this instruction helpful
I used a flat screwdriver and released the lock tab on the bottom of the light switch, and pried the switch out, being careful to not damage the plastic around the mounting place of the switch, unplugged wiring from old switch, plugged in the new one and pushed the new switch into place. Job finished light switch now working.

Plastic broke where motor mounts to dispense ice so motor was just lying on the back of the enclosure.

  • Customer: Thomas from Chandler AZ
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Wrench set, Wrench(Adjustable)
  • 26 of 29 people found this instruction helpful
Removed Enclosure, removed solenoid, removed yoke from motor, installed motor and installed solenoid. Then re installed enclosure.

The difficulty was removing yoke from motor shaft, left hand threads that were hard to identify. No place to hold shaft so it turned when trying to remove yoke.

Some minor difficulty re attaching electrical harness for motor and solenoid as I had to do it by feel. Removal was easy as the motor was just hanging and I removed the solenoid before removing the enclosure.

There was a chattering Noise from Adeptive Defrost Assy

  • Customer: Herman from Hughesville PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 25 of 27 people found this instruction helpful
I first dropped the Cover Assy, which covers lites and controls, this was done by pulling it forward and it drops down, did not remove top shelf so It was a bit difficult to tilt cover assy. for removal. There is a srew located close to filter assy. in back use nut driver 1/4"located to remove this screw, there are then 2 screws located to the rear and side of light holders, both phillips head, the one on the left side is a bit tricky to remove but I use a thin bladed scredriver, Next there are 2 screws located on both ends od the slides that control temp, both again removed witn1/4 " nut driver, the whole upper assy drops down and forward the Adeptive Defrost assy is located in the back right corner of this assy, unplug the wires and unit snaps out, I foud it easier to pop off top cover of new unit so I could see connector assy when I reattached the wires, then replaced the top assy and snapped new unit it place, Reassymbly was reverse of removal, before placing cover assy back in place I replaced both lamps as 1 was out .

leak from back of refrigerator where water line enters ice compartment

  • Customer: Michael from Tucson AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 34 of 54 people found this instruction helpful
replaced old water fill tube for ice maker because it would clog with frozen water which would result in leaking from back of refrigerator where water line for ice maker entered refrigerator. Parts arrived faster than anticipated from parts select. New part was made differently (up-graded) so that water would not freeze. removed old fill tube and replaced with new. replaced water tubing and secured. leak is no longer present and I do not anticipate further issues from this problem. Thanks Parts Select

Refrigerator warmed up and freezer became colder

  • Customer: John from Cambria CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 23 of 24 people found this instruction helpful
After removing all shelves, I removed the 2 screws holding the 2 panels in front of the evaporator and heater. The heater is located at the bottom of the evaporator coils and is held on by a simple wire clip. After removing the heater and thermostat, is very easy to replace the new unit and reconnect the wire harness.

Had to replace a hose connector at the base of my refrig/frreezer

  • Customer: Leo from Salem SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 30 of 46 people found this instruction helpful
Perhaps a helpful hint:

When aI received the hose adapter/connector, I inserted the 2 hose ends only to have water drip from the connection.
I used a utility knife to remove an inch from each side, then reinserted the hoses. That made the differnce. Dry as a bone.

LG

shut off arm broke

  • Customer: Thomas from Va. Beach VA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 27 of 42 people found this instruction helpful
open ice maker door, use mirror to view slot in front of ice maker, slip piece in place and done

Refridgerator/Freezer Not Cooling

  • Customer: Melinda from Modesto CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 21 of 24 people found this instruction helpful
First of all, let me say that I'm a 50 year old single woman. If I can do this repair, anyone can! After unscrewing the back of the unit that houses the compressor, I found the relay overload switch which is attached to the compressor. I pulled the part off and discovered that it comes in one piece. The replacement part came in 3 pieces. I intially thought they sent the wrong part. After a little thinking outside of the box, I figured out that the replacement part was indeed the correct part and that it comes in 3 pieces instead of one. It would have taken 5 minutes to repair if I had realized this early on. Once replaced, the refrigerator/freezer was cooling within 10 min. I sent the Run Capacitor back after telephoning a customer service rep. She was so courteous and helpful! What a fabulous company. I highly recommend. I saved myself approx. $250.00 doing it myself.

Refigerator not cooling

  • Customer: Ronald from Katy TX
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set, Wrench(Adjustable)
  • 25 of 37 people found this instruction helpful
Through experience I determined the problem was with the compressor trip switch. It's the small white piece that looks like a flat fuse.

The parts arrived in 3 working days. Instructions were included - very easy to understand. From start to finish I replaced the switch in about 15 minutes. Frig is now working perfectly.

3 pieces come along in the kit - however, all I needed was the switch, but for the price I changed out all three to assure compatibilty.

I also ordered the cover which was not needed.

A Happy Customer! {:-)

Refrigerator would not defrost and was abnormally warm inside both compartments

  • Customer: Conrad from Northville MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 19 of 19 people found this instruction helpful
The adaptive defrost assembly is located in the refrig compartment. This requires removing the panel which covers the temp controls and interior lighting. In the back right hand corner is the adaptive defrost circuit board. It has a six wire connector and is retained by two screws.

Remove the two screws and grip the connector making sure to disengage the locking tab with holds the connector in place.

Replace with the new assembly by plugging in the connector, replacing the two screws and then reinstalling the compartment cover.

Set the temperature lower than you normally would temporarily to make sure that the system is working properly (takes 30 - 45 minutes).

Once the unit begins to cool again, you can gradually readjust the temperature to it normal range in both the freezer and refrig compartments.

I used a flashlight and a mirror to check the coil in the freezer compartment for a couple of days to make sure that the defrost function was working correctly by looking up into the louvers and observing if there was any ice accumulation.

Easy repair and Partselect provided great on-line information. Also, I probably saved a bundle.

doesn't get cold at all and freezer was warm condenser wouldn't run

  • Customer: Jean from Fremont CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 20 of 24 people found this instruction helpful
removed all 6 screws in back of fridge. located the condenser the relay was a white like circut to the left of the unit. The entire pience comes off easy using a flat screw driver to pry it off the pins.
The replacement came in 2 pieces insted of 1.
I replaced the relay and then the overload reconnected the wire harness back the way it was before. The new relay has a larger connector prong for the live wire so the kit comes with a jumper wire so the original wire harness can be used without splitting the cabel made the repair very easy. Also the new capacitor is bigger and better so I replaced that as well. The capacitor makes sure the relay gets stable current so its good to have a working one.

Icemaker was dumping water into ice bin and the ice maker shut off arm broke its rear mount

  • Customer: GORDON from CUPERTINO CA
  • Difficulty: Very Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 24 of 37 people found this instruction helpful
First I removed the 14.3 tons of freezer contents, closed the water valve, shut off the juice, and removed the freezer bins, the freezer door and the three screws that held the element in place. After bringing in 397 hand tools from my garage inventory, I loosened the unit and, after extensive evaluation, I finally disconnected the wiring connector from its freezer rear wall connector counterpart. You ain't gonna believe the rest of my story--of total ineptitude by an experienced fix-it-yourself dummy.

I searched the internet for a replacement ice maker and found it at partselect.com. I called Sears to ask if I could add my refrigerator to my existing appliance repair account. Sears said sure--it would cost me only one arm, three toes and one grandchild. I abruptly declined their magnanimous offer—I don’t give up my arms and toes so easily.

I visited the local Maytag repair parts and service retailer, who advised they didn't do parts anymore. Expecting their repair price would be greater than Sears, I resorted to partselect.com. I called them to be assured what I was buying was not mistakenly a 747 Landing Gear. On the afternoon (West Coast) of 4/28/10, I ordered (via internet) one PS21215123 Ice Maker Assy. Much to my pleasant surprise, it arrived via FedEX on 4/30/10 (no freight charges to me).

My repair/replacement efforts were hampered by the effects of my right rotator cuff surgery a few months before and major left wrist surgery two months ago to remove fractured bones and torn ligaments.

Undaunted by my physical handicaps, I forged forward. After re-installing the unit, I turned the water supply and electricity back on. It was graveyard dead. I wisely then bought two bags of ice as an interim solution to the severe needs of my wife and me for our daily chilled evening cocktails. I removed the unit, checked it out and re-installed it. I bought two more bags of ice. All the while, I turned the water and electricity off and on as required by reasonable safety standards. High tediousness!

Several more home maintenance tasks then arose for Sergeant Super Fixer, but I returned to the ice maker problem on 4/8/10. Last chance--remove the device and insure there was no frozen ice in the inlet tube--or call the local partsless repairman. No ice found, but I did learn the wiring connector to the unit was awry--no contact! While explaining that to my wife, I realized the two upper mounting screws were intended to be partially installed into the freezer wall to accommodate the unit's slotted mounting holes! Then, tighten the screws. Oh my God! During my 143 installations and removals, I had installed those screws blindly--using the (handicapped) skills of my right and left hands without any benefit of direct eyesight.

I returned to my challenging project this morning (4/9/10), fully utilizing all the expertise I had gained yesterday. Fifteen minutes of amusing effort! Turn on the juice! Turn on the water!Two hours later, ice cubes were dropping into the bin like rhinoceros bisquits in the jungle.

Hallelujah! I now am free for the next challenge!

HINT: Put a bed pillow (an old one, or your wife's) in the freezer compartment to soften the harshness of its cold metal on your back, if you use the "crawl in on your back" approach.

Compressor "grounded" and quit running

  • Customer: Mike from Baytown TX
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Wrench(Adjustable)
  • 39 of 82 people found this instruction helpful
Replaced the compressor with the new one I purchased from you. Installed new parts and recharged unit. The refrigerator / freezer is working better than new. Thanks for the great deal on the compressor. It was here in 3 days. All the parts fit exactly and had no difficulty in the installation or startup. The directions for the wiring were a great help also. Thanks again.

Icemaker arm was broken

  • Customer: Jason from Austin TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 19 of 24 people found this instruction helpful
The tiny piece of plastic that holds the wire that shuts off the icemaker, broke early on with our fridge (after just a few months.) We superglued it, but last week it bit the dust for good.

Once I got this part, I removed the freezer door and trays, and pulled the icemaker out by removing 3 flathead screws and unplugging the cables. Laying in the freezer on the floor was a bit unconfortable, but not too bad.

Then I inspected the icemaker. There was no obvious way to remove the part without disassembling the front of the unit (where the motor is) to release the spindle and free the part, so I did that - 3 or 4 nuts was all that held it together. Once that was out, I removed the spindle, swapped out the part, and put it all back together and back in the freezer. Plugged it in and waited.

It took a while to start making ice. Like 5 hours. Now it's going pretty slow (much slower than before.) Haven't had time to look into it, but my suspicion is the rubber hose that feeds water into the icemaker is blocked with ice or kinked. In any case, we have ice now (but not a lot), and the unit shuts itself off properly. However, we went from having too much ice (thing never shut off) to too little (thing makes ice too slow), so I need to shoot for somewhere in the middle ;)
All Instructions for the MZD2766GEB
16-30 of 833