TOOK OFF TOP AND FRONT PANEL REACHED IN UNDER TUBE AND REMOVED FROM BELT TENSIONER HARDEST PART IS PUTTING BACK ON TENSIONER TAKES TWO HANDS LAYING ON YOUR BELLY
Un plug the dryer. Gather phillip, flat head and torix screw drivers. Remove the rear of the dryer to get the spec sheet with the appropriate part number. Next called for part. Belt installation requires removal of front and top of dryer in order to slide belt over the drum. Getting to all the fastners requires tilting the dryer on its back. Clean out excess lint from dryer interior and duct work. Slide drive belt over drum and use some masking tape to hold it in position. Reassemble dyer. Return dryer to upright position and put the belt on the pully and tensioner from rear access port. Remove tape. Replace access panel. Reattach vent duct work. Plug in. There are 5-6 different size screws holding everything together...you may want to use masking tape to label where each type of screw goes. All totaled it took about an hour and cost less that $25. Well worth the effort.
After not being able to get the proper 10 foot hose, and having to splice two drain hoses together....turned out it was not the drain hose after all, but the pump. Some sort of "baffle" in the drain hose, where the rubber connector at the pump end and the corrugated hose joins, was blocking the water I thought. It may have been since a spliced the new hose in at that end. However, I think it was the pump.
i took the hose of and stuck the water hose in it and saw a lin hole leak. i order a new hose and recived it very fast (1 day) took 15 min to put it on the pump and to put the machine back togther
At first I thought the o-ring may have wear out so I took the pump out to check, but the leak was either from the shaft seal or body itself (hard to tell as body had corrosion on it) taken out the pump was very easy, but you need to use the right pliers to easily remove the spring clamps. Follow instruction to set the housing orientation, and than install back the pump. Reinstalling one of he hoses using the spring clamps took few tries, but it was in place in no time. remember not to install the cover before you operate the washer to verify no leaks. This work is realy very very easy.
Drain hose should come with the two clips (45B)that hold the drain hose to the back of the machine. I had to cut the old hose off. Then very carefully remove the clips from the inside of the machine with a pair of pliers.
took of the front cover. then i took off the plastic cover on top of the water pump. then i unbolted the water pump and disconnected the hoses. i had to rotate the water pump connections. i swap the base of the pump and then bolted it back in place connected the water hoses back and then put the plastic cover back on. and to finish i put the front cover back and i was done.
Well, the intall would have been great except for the fact that I needed another part. If your belt breaks there is a reason for it. Make sure you check all the parts that work with the belt. Their was a pully the was defective and also need to be replaces. I think it would be a good idea to put a little note on the page for the Belt Drive to let people know that if you are replaceing the belt you might want to check the Idler Pully for it too might need to be replaces. I'm not an expert and if that was on the page for the Belt Drive I might have look at the pully before I ordered and I would have ordered the part along with the Belt Drive. As it was had to wait another 4 day to get my dryer fixed. I'm very happy the Parts Select has all my parts and they pretty good at getting them out to me in a good amount of time when I need them.
I had replaced the pump 5 years earlier and now it was leaking again. When I removed the old pump, I discovered a bobby pin had made its way into the pump and was chewing up the housing, causing a small hole. This was a very simple repair as the pump sits right in the bottom front of the machine. The most difficult part was removing the old hoses and re-attaching them to the new pump. Four bolts/screws and two electrical connectors, which cannot be confused, made this an easy fix.
Fairly easy repair to replace the discharge pump assembly. Remove the access door, pump shield, disconnected the hoses, remove the hoses, and the pump housing screws. Orientation of the water pump had to be changed to match original, easily done by rotating the pump hosing. Installed in reverse order and job was complete