Models > MH1150XMQ0 > Instructions

MH1150XMQ0 Whirlpool Microwave - Instructions

All Instructions for the MH1150XMQ0
196 - 210 of 242
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Old light bulb popped and burned out and melded itself to the socket. Light bulb then broke off inside the socket. Socket cracked and broke when trying to dislodge broken light bulb.
Removed all the screws from the underside panel - approximately 9 or 10 of them. The panel easily dropped down to allow easy access to the light bulb socket assembly. The wires to the socket easily unplugged and old socket easily removed. New socket slipped right in and wires easily plugged in. Actually took longer to put the screws back in than anything else. I am thrilled with this repair. Note: so easy even a 61 year old single woman in her PJ's can do it.
Parts Used:
Light Bulb - 40W Light Bulb Socket and Housing
  • gail from charlotte, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
plastic clips & pieces of original vent broke off and vent grille would no longer lock in place.
Ordered new vent part. Just set in place and fastened screws. These parts do not last because the plastic does deteriorate.
Parts Used:
Vent Grille
  • Michael from Naples, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The grille vent broke on my microwave wasn't sure how I was going to get a replacement part found this web site and the part I needed. Good price and received in less than 24 hrs.
Simply place the grille on microwave and tightened the screws
Parts Used:
Vent Grille - Black
  • Donna from Monroe, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Burned out light bulb
Replaced light bulb.
Parts Used:
Light Bulb - 40W
  • Ray from Gatlinburg, TN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Broken. Grill vent
Removed broken grill and small plastic pieces from unit. Removed screws. Cleaned filter. Inastalled new grill and installed screws. 10min. Job.
Parts Used:
Vent Grille - Biscuit
  • Ken from Rapid city, SD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
broken grill
remove two screws place grill screw two screws
Parts Used:
Vent Grille - Biscuit
  • Kathryn from Angel Fire, NM
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
broken grill vent
pop it in and used two screws, no problem.PS, this is a great company to deal with. I ordered wrong color and was replaced with proper part within three days.
Parts Used:
Vent Grille
  • Dennis from Miamisburg, OH
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Microwave turntable stopped rotating.
1. Unplug the power cord from the wall socket. 2. Remove the 10 screws holding the bottom cabinet cover in place. The bottom cabinet cover will swing down allowing acces to the inside ofe the microwave. 3. Remove the connector from the turntable motor. 4. Use a T15 Torx driver to remove the 2 Torx screws holding the motor in place. 5. Remove the motor. 6. Reverse the process using the new motor.
Parts Used:
MOTOR-TURN
  • Larrt from Minooka, IL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Replace Vent Grill
Removed old grill and replaced new grill with no problem
Parts Used:
Vent Grille - Black
  • Samuel from Mitchellville, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
replace light blub
removed grill cover, removed bulb plate, unscrew bulb, screw new bulb in socket,put bulb cover back on and screw grill cover back on. no issues whatsoever.
Parts Used:
Light Bulb - 40W
  • roger from palm coast, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Broken grill mounting points.
Replaced the grill. Easy.
Parts Used:
Vent Grille - Black
  • Donna from Louisville, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Glass cooking tray for microwave cracked.
All I had to do was lay the new tray in the microwave. Easy as pie. Also, the new tray arrived very quickly.
Parts Used:
Glass Cooking Tray
  • Sharon from Kannapolis, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Broken plastic around screw holes.
Make sure that the screws go in the holes, after you put the grill in place.
Parts Used:
Vent Grille
  • Robert from De Pere, WI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
grille kept falling off until tabs broke
Looked at the original instruction manual to see how it was installed, removed the two Phillips screws, fitted the grille into position until correct, then replaced the two screws.
Parts Used:
Vent Grille
  • Marcelene from Cuyahoga Falls, OH
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The small connector flaps broke off so the grille wasn't attached.
With a phillips head screwdriver I removed the screws, which were screwed to the then non-existent grille, at the top of the grille holder, GENTLY popped the new grill into place and replaced the screws. It took about five minutes. As a housewife, I feel that doing these little repair jobs around the house saves my husband time and aggravation. It was all very simple, and I got the ordered part in two days. Fabulous!
Parts Used:
Vent Grille
  • Clarissa from Fallston, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the MH1150XMQ0
196 - 210 of 242
Back to Top