MGR4452BDW Maytag Range - Instructions

Removed bottom tray in oven, used nut driver to remove igniter, pulled oven out from wall and unplugged cord, did steps in reverse and repair was done. Very good tip on what was wrong with oven and how to diagnose the problem. I will defintly use your tips and purchase parts from you in the future if the need arises.

Checked troubleshooting guide on website / ordered part / replaced part by removing two screws in oven on bottom pan/ removed inside oven bottom for easiy access/ removed two screws from bracket holding down the heating element/separated the electrical plug in back releasing the wires to heating element/ installed the new element with two screws / connected the electrical plug/ installed the bottom panel inside oven / installed two screws inside oven on bottom panel. Checked operation of unit- gas lit ok - pushbutton panel did not increase heat seting properly/ dismantled the control panel / dismanteled the circuit board / found remains of several roaches inside circuit board recess/ cleaned all pushbutton points and re-assembled unit - all worked fine except when oven burner went off - the gas valve would not shut off completely - leaving a small flame burning at the gaaas valve orifice "DANGEROUS". I checked troubleshooting guide again / ordered a new valve - installed - (did not come with a new Propane orifice ) - had to use old one ( should have either asked me or just sent one when I ordered) - received new valve - installed with old Propane orifice - all works well now.

i ordered the part, it came in speedy quick,and it was very easy to install i saved $200 bucks, and my mom was the happiest person in the world. thank you.

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

removed the old defective ingniter and installed new igniter turned on the ove n and wala, it was like brand new.

snaped them into oven cavity attached temp bulb job complete

part was purchased as spare because when the ignitor goes bad no warning is given it just fails.

very easy

First I unplugged the range, turned off the gas to the oven and disconnected the gas line from the oven. I pulled the oven out to gain access to the rear of the unit and unplugged the old igniter. Next, I removed the oven door, removed two screws to the floor of the oven and removed it. I then removed the metal covering above the gas component allowing full access to the igniter. I removed two screws from the igniter and removed it. I positioned the new igniter and replaced the two screws. I replaced the covering over the gas component, replaced the oven floor and put the oven door back on. I went to the rear of the unit and plugged in the new igniter. I then reconnected the gas line to the oven range and checked for leaks, No leaks were found and I pushed the oven unit back into place. I pushed the Bake button and the igniter started igniting the oven.

Job completed.

1. Turn off the gas (propane)
2. Unplug the oven.
3. disconnect the gas line and pull the oven out.
4. remove the back panel to access the igniter.
5 disconnect the igniter.
6. unscrew igniter/gas assembly and remove from oven (two screws).
7. unscrew igniter (two screws)
8. replace igniter with new.
9. reassemble in reverse order.
10. turn on stove.
11. Happy wife, happy life.

I simply pulled the stove away from the wall, disconnected the gas and electricity. Then took the pan out from stove. At which time I used a socket to remove the two srews and then unplugged the part from the back of the stove. After that, reattached the screws, plugged it in, reconnected the gas and electricity, and pushed the stove back against the wall. Fired up the oven and it has worked like a champ ever since!

First I called a local repair shop and after getting a 325.00 repair estimate I looked up your website and discovered that I could purchase the part for 46.00 dollars and followed the do it yourselfers imput Now thats what I call a savings

Removed oven bottom were you see the light glowing from then unscrewed igniter unpluged then took it out and put in new one went well i would do it again works great

Remove oven floor and bottom drawer
remove 2 1/4-inch screws holding ignitor
remove cover plate behind drawer to access P/J
Disconnect plug remove ignitor and reassemble

Did not have gas smell, but ignition took 6 minutes

removed 2 screws on element then unpluged it then replaced it with new one easy job