MER6770AAW Range - Instructions

I removed the old sensor via the two screws holding it in, unplugged it and replaced it with a new one.

I ordered both the light bulb and the switch that controls it. I had not pulled the stove out because the ones I bought this house from did not level the floor which meant I had to wait on a socket set to arrive in order to be able to pull my stove away from the wall. Once I got the socket set and the stove out I removed the panel on the back. I saw then that my red light bulb had shattered in half forcing the switch to just hang free. Glad I had ordered both parts, removed the old, replaced new with ease... then it was a matter of sliding the panel back in place without the main control panel getting misaligned, few trial and error checks and it went back with ease. New light works! Very easy.. probably less time if your floor is level.. then I had to play with the little legs to get it even again. For now it is ok until the spring where I go to redo the floor and make it all LEVEL! Very easy! Hope it doesn't burn out again but if it does I know what to do! Maytag rep wanted to charge me $100... No thanks!

Removed the oven door (very simple) removed oven racks. Using an ordinary phillips screwdriver removed the two(2) metal screws holding the element. Carefully pulled the element out far enough to disattach the two flat bladed electrical wires, being careful not to let the wires fall back inside the oven wall.Install the new element in the exact reverse order. Even if the two wires should slip back inside the oven wall it would be a simple matter to remove the 6 metal screws holding the rear cover of the range to retrieve the wires.... All told it was a very simple and quick repair job. Best of all there was no repair man fee.

Removed two screws holding cooktop to oven. Unlike the video, the cooktop was not detachable as the wires were hard-wired to the range, so I had to prop the top up with a 6" block of wood and was working upside down. I replaced the element and everything worked just fine.

Repair video was very helpful. I have removed the screws on both sides of the appliance under the surface plate, in the front. The Owen door has to be open for that. Then I have pulled the surface plate for a little space to disconnect the two connectors. Turned the surface plate over on the kitchen table, removed the 6 screws. Turned the burners assembly over and removed the small burner by disengaging the two clips. I have removed the 2 clops from the burned burner and assembled it to the new burner. I have placed the burner and engaged the 2 clips with a crownose players. I have removed one electrical connecter at a time and connected to the new burner. I have turned over the assembly over the glass plate and assembled the back cover with 6 screws. Put the surface plate on the range and connected the 2 connectors, pushed back, lined it up with the 2 screw holes in front of the range on bot sides and put the 2 screws in and Finished.

The difficult part is finding and training the right husband. First, he must be handy and second willing to work on 'honey do' projects. Praise the Lord, I have such a husband. He went on line, found the part needed, ordered it and when it was delivered, fixed the oven. You see he loves his cornbread and muffins, so it was to his advantage to fix it.

remove 4 screws plug in wire carefully replace 4 screw with new 2 top one side larger

Turned off the power, undid two screws, pulled heating element out, used pliers to disconnect bayonet electrical connections, then installed new element. Took about 20 minutes.

Disassembled upper unit with Phillips screwdriver. Removed 2 "plug connectors" from element switch. Replaced switch. Plugged both connectors back onto switch. Reassembled the upper portion of the range. Tested and OK

This job replacing the was so easy, it took about ten min,to do it thanks

my husband unscrewed the screws in the back of the oven and replace the element. Fairly simple

Easy just loosened screws took apart door, removed broken glass and installed new glass.It took longer to clean the stove! Lol!

The hardest part was deciding if this part would fix the problem. The upper oven became unusable. Both elements worked fine until reaching temperature. The oven would not come back on after that. I took two screws out. Then I pulled the wires out and unsnapped the coupling. The install was reverse. I just snapped the coupling in place and replaced the two screws. All works fine now. Saved a couple thousand as wife was prepared to buy a new one.

Remove two screws at back of oven. Pull the element out, remove the electrical slide connectors. If the electrical wires fall back through the openings, pull the range out from the wall to access the back..remove the small cover panel at the lower left and you will have full access to the connectors. Put the new element in place, connect the electrical connectors and replace the securing screws. Replace the back cover panel if you removed it. Job finished.

turned power off to oven removed screws that held heater, installed new, very simple