Models > MER5755QAQ > Instructions

MER5755QAQ Maytag Range - Instructions

All installation instructions for MER5755QAQ parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MER5755QAQ
61-75 of 201
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven not heating pass 125, heating element not working

  • Customer: Damaris from Ocala FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 2 people found this instruction helpful
First I removed the screw behind the stove that hides the electrical wires. Pull off the two wires connecting the bake element with pliers. Unscrew the two screws holding down the floor pan which covers the baking element and pull out the floor pan. Here you will see the baking element, it is attached with a few screws. Remove the baking element and attach the new the same way.
We could not believe how easy this repair was to do. Not to mention all the money we saved on a repair man.
Thank you partselect.com, I'm glad I researched this on the net.

Replace the oven Sensor

  • Customer: Michael from Exeter NH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 3 of 5 people found this instruction helpful
The sensor is mounted in the top right side of the oven.An extra long screw driver helps to avoid damage to the sensor when replacing it.The connectors were the opposite to the old sensor and I did not see that there were adapter cables included. It might help to connect or tie these together as I only expected the sensor and did not look for adapters.I had cut the wires and used wire nuts when I found the adapters.The repairs works fine.
Mike

Bake element went out

  • Customer: Jeff from Vancouver WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
First I removed the two wires from the back of the stove. I then removed the two screws that were holding the element in place. Installed the new one without problems

the old gaskt was not linge dup well, the door was not closing well

  • Customer: mohaemd from pittsburgh PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
pulled the old gasket, the new one fitted perfectly. No effort at all.
An instruction sheet would be a bonus. I wish you put instruction sheet in all parts OR a web link for video instructions. a web link would be great

Oven tempature would not exceed 165 degrees.

  • Customer: Michael from Torrington CT
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
Purchased new bake element from PartsSelect. Very easy to install, unplug range, remove 6 screws, slide element out and unplug end, remove old element. Reverse procedure to install new element. My range was about 6 years old and in excellent condition, was considering buying a new range. Found PartsSelect on-line and ordered new element. Their website is very easy to use and find correct parts.
Saved lots of dollars, this PartsSelect website and service is great.

Indicator Lens melted and fell back into the control panel

  • Customer: Philip from Houston TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
I took the back panel off, removed the old lens, installed the new lens. How easy to order from home, receive the part, do the repair and pay less than it costs to simply drive to the parts house. Cool....

BURNER ELEMENT REPLACED

  • Customer: GLENA from CINCINNATI OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 3 people found this instruction helpful
MY GRANDSON, AGE 15 DID THE REPLACEMENT. NOW, HOW EASY IS THAT!

blown heater element

  • Customer: mark from otsego MN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
Pull oven away from wall and unplug. with the oven door open, remove 2 rear screws holding down the element cover and pull element cover out of the oven. remove 2 screws holding element down to the bottom of the stove, and one screw holding the back of the element to the rear. now go behind the oven and remove the access plate to the element power connection (one screw). Disconnect the 2 element power wires. remove element. to install, reverse these instructions

ovens wouldn't maintain temperature after preheat cycle

  • Customer: sherri from elk horn IA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
unplugged oven. removed 2 screws that hold the sensor in place, then removed the dozen or so screws that hold on the rear panel, unplugged sensor and fed wire through insulation. identified and installed correct harness adapter then fed new wire and connecter through insulation and connected to adapter. installed sensor retaining screws.plugged oven back in and tested function.no dice. unplugged oven once again. removed oven control panel and upon inspection of printed circuit board discovered 3 solder joints had failed. dang. resoldered failed joints and also sweetened up a few others that looked suspect. reinstalled controller, replaced all retaining hardware, and plugged in the oven. tah-dah!! works like a charm now. moral of the story is check the pc board first and save $50 for unneeded pats!!! or buy the controller from parts direct for $260ish. btw a roll of solder and soldering iron from an auto parts store cost around $10, learned to solder on you-tube $0. amazing all the home appliances yo can fix if you're not afraid to take a few screws out and poke around a bit. CHEERS!

broken oven door inner glass pane.

  • Customer: Adam from modesto CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 3 people found this instruction helpful
Remove the door, remove screws from all sides

Remove sides and face of oven door by sliding down from under the oven handle trim.

Remove screws on 2nd light of glass and set aside.

Now you are at the inner door panes. their should be two in an insulated type unit.

Remove the remaining screws from the handle pracket and the permiter frame for the glass/insulation. Remove permiter frame and set aside.

Pull out inner door glass frame. get a pair of pliers and bend tab on frame up so you can pull the frame sightly apart, replace the glass, secure frame tightly around glass slide tab back into reciever slot and bend down ( you may need another person to assist in keeping both lights in the frame while trying to ben tab back in to place)

reassemble door as it came apart carefull not to over tighten the screws, they strip easy.

The heating element for the oven section was luke warm even when the control was turned up high.

  • Customer: lawrence from Laurel MD
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 3 people found this instruction helpful
I wasn't sure if it was the heating element or the temperature probe not allowing the oven to go above 200 degrees so I ordered both from Selectparts. After receiving my replacement parts (in record time thank you) the oven element had a hidden slit on the underside near the connection. During its removal the element disintegrated at that point.

Since Maytag is very user friendly to maintain, it was a matter of removing the retaining nuts securing the element to the back of the oven, and resecuring after replacing with the new element. I did have to take the back panel off the oven to reattach the wiring to the element. This was necessary because while I was removing and replacing the element, the insulation was pulled through the access holes. I also replaced the temperature probe because I had already ordered it. This was easier to replace however and I did not encounter the isulation problem as I had when removing/replacing the element. I recommended your company to my friends and would definately order parts from you should I need to repair another appliance in the future. Thank you again.

Broken levelling leg

  • Customer: Linda from Oneida NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 6 people found this instruction helpful
Took the old levelling leg out and screw the new one in.

Shattered inside glass when attempted to self-clean

  • Customer: John from East Sandwich MA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
Door was removed very easily. Outside trim pieces were removed. The rest came apart like a simple puzzle. Inside glass is very easily accessed. Upon assembling, time was well under an hour. Shipping was fantastic and I saved close to 200dollars between a service call and a repair.

Inner glass pane broke during self-cleaning operation

  • Customer: Mark from Abingdon VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
I removed all the screws that held the trim and inner frame to the outside window unit first. Then, I removed a protective glass from over the two inner panes. Next after removing the frame that held the two inner glass panes together, I took the broken inner glass pane out and replaced it with the new one. Then basically I just retraced my steps and had the door put back together in about 45 minutes. You just need to pay close attention to your disassembly so that you are able to put the pieces back together quickly.

Failed Bake Element

  • Customer: Chad from Johnston IA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
First of all, let me say how "Not Handy" I am when it comes to these things. I decided to give this part a try after my oven decided to fail on Thanksgiving Day, so I ordered the part. It arrived on time as promised and packaged very well. The on-line parts breakout and testimony from the other buyers were so helpful. I had our oven back up and running in less than 10 minutes.

One thing I would also recommend is that you burn the element once installed for at least 15 minutes to get the newness smell off of it and then it won't permeate your food items.

Thanks, Parts Select! You saved me over $900.00; the price it was going to cost me to buy a new oven. :)
All Instructions for the MER5755QAQ
61-75 of 201