Turn off breaker to oven and verify no power. Remove the two screws holding metal panel covering baking element on the floor of the oven (near back of inside of oven) Remove two screws holding element mount to floor of oven (near front of inside of oven). Remove single screw holding element to back wall of oven. Pull element toward front of oven, carefully holding wires so they do not disconnect from element and slip inside the ovenback wall. When you can reach the wire connections, hold each one with a pair of pliers and disconnect from element ends. Connect new element ends into wire connections. Be sure to insert all the way into both connectors. Carefully, push the wires back into the rear of the oven, trying not to scrape the wires on the sheet metal. When fully inserted, reinstall single screw to secure element to back wall. Re-install two screws to element mounting at the front of the oven floor. Re-install two screws to secure element cover plate to the floor of the oven. Turn on breaker for oven and verify oven has power. Turn on oven to bake at 400 degrees. Wait for oven to come up to temp and maintain for 10-15 min (you may smell some burning smells as the element heats up the first time). Enjoy...
First I removed the two wires from the back of the stove. I then removed the two screws that were holding the element in place. Installed the new one without problems
piece of cake. The pictures with the grid background on your website gave me ability to verify what I was purchasing.
This is the second use of Parts Select. First time was for another obscure part for an old microwave, which also worked out VERY well. Both appliances still in action.
Inner glass pane broke during self-cleaning operation
I removed all the screws that held the trim and inner frame to the outside window unit first. Then, I removed a protective glass from over the two inner panes. Next after removing the frame that held the two inner glass panes together, I took the broken inner glass pane out and replaced it with the new one. Then basically I just retraced my steps and had the door put back together in about 45 minutes. You just need to pay close attention to your disassembly so that you are able to put the pieces back together quickly.
Bottom oven door handle broke when someone tried to open door too soon following self-cleaning cycle.
We removed the door from the hinges by sliding it up. Then we removed all the screws holding the door together. We had to remove the screw securing the trim. Next we removed the screws inside the trim holding the old handle. We replaced the handle and trim and screws in reverse order. Finally, we re-attached the door by sliding it onto the hinges.
ovens wouldn't maintain temperature after preheat cycle
unplugged oven. removed 2 screws that hold the sensor in place, then removed the dozen or so screws that hold on the rear panel, unplugged sensor and fed wire through insulation. identified and installed correct harness adapter then fed new wire and connecter through insulation and connected to adapter. installed sensor retaining screws.plugged oven back in and tested function.no dice. unplugged oven once again. removed oven control panel and upon inspection of printed circuit board discovered 3 solder joints had failed. dang. resoldered failed joints and also sweetened up a few others that looked suspect. reinstalled controller, replaced all retaining hardware, and plugged in the oven. tah-dah!! works like a charm now. moral of the story is check the pc board first and save $50 for unneeded pats!!! or buy the controller from parts direct for $260ish. btw a roll of solder and soldering iron from an auto parts store cost around $10, learned to solder on you-tube $0. amazing all the home appliances yo can fix if you're not afraid to take a few screws out and poke around a bit. CHEERS!
Hired a pro. Parts are difficult to get on a timely basis today , if at all. Screw up this repair by damaging the outer " black glass " and you buy a new stove. It took three weeks to get my replacement glass even though PS said the part was being sent within a day of the order. Even so , I am am happy to have gotten it , and will continue to use the company.
First things first...Unplug the unit...Then remove the center plate from the back of the oven (one screw) and take clips off element. Then on the inside, there are 2 screws near the back on the bottom panel. These were rusted on pretty good, so that's where the vice grips came into play. The entire job would've gone much faster, if I wasn't fighting with these 2 screws...After you remove the screws, tilt up bottom panel and remove. Then you just remove 1 rear screw & 2 bottom screws and slide out the old element. Slide the new one in, secure it with the screws and screw the bottom panel back into place. Go to the rear of the oven, slide the 2 clips on the element and screw rear plate back on. Plug the oven back in and that's it...
Oven erratic, not heating correctly, timer beeper sounding
The video indicating •unscrew old sensor, •pull wiring, •unplug old sensor, and •plug in replacement was good until I pulled the old one and saw wire nuts behind the small square hole! After some research, I learned that the nuts COULD come through that small hole with use of needle nose pliers. One of the wire nuts had the edges pinched off (chipped) in the process. Then I learned about ceramic wire nuts, which I'd never previously encountered. Very important if you don't want to melt your nuts! I cut and stripped the end of a disconnect plug to the stove wiring and now I have a plug in place; which, hopefully, I'll never need to use.
It was easy to remove the old oven door gasket. Just a little tug was all that was needed. Installing new gasket was just as simple as tucking in the gasket end into the hole at the bottom and pushing the clip in the corresponding hole. TIP: roll the end of the gasket and feed into the hole then use a small tipped screw driver or the point of a needle nose plier to finish installing the ends into the hole at the bottom of the door opening.
Oven sensor caused cooling fan to run continuously. Had to flip breaker to get it to turn off..
Left oven off. Located sensor in pdf manual. Unscrewed mount, pulled sensor out to access connector. Disconnected old sensor, checked continuity(resistance) on ohms with multimeter. No continuity; connected new sensor, screwed mount back into place, turned on oven and baked cookies to check operation & it worked perfectly.
