Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
I leaned on the door and broke the hindge
I had a lot of trouble unlocking the door hindge you must pull the door out to change the hinge they are on the hinge and slide foward then pull the door up and out lay the door flat on a table cover the table with a towel so you don't scrach either one. Unscrew 6 screws on the door cover. 3 on top 3 on bottom take the cover off the hinges are exposed there 3 screws on the hinge 1 on the front and 2 on the bottom replace hinges install face insert door and lock the hinge it's all done. I wish I had these directions
I removed the door from the oven and set it on towel on the table, and started the repair of the door. I removed the screws one at a time, and one layer at a time. Becareful you need to take the whole door apart, and remember how it goes bact together. In the end it was worth it. The hardest part was getting the right part. I thought I could order the whole door, and found out after several calls they don't sell the whole door. Part Select both times I put in my order had the parts at my door within 2 to 3 days. I also had to return one of the parts and within 2 to 3 days the part was credited to my account
I first removed the drawer from under the oven, then I used 2 strips of packing tape to hold the front glass in place. Next I loosened the 4 screws on the bottom side of the door to the point just before they would fall out. Next I had someone help hold the glass as we removed the tape and slid the glass from under the handle and set it aside. Once the glass was off I removed the 4 screws on top of the door and the 4 screws (2 each side) holding the handle brackets. From that point it was just a couple of screws on the back of the handle to swap the broken part for new and reassembling everything. Could be done in 30 minutes, 40 by yourself. Maytag wants $24 to tell you how to do this, it's not worth the money. Also, PartSelect.com sold me the part for 30% than Sears or Maytag advertise - they've earned a permanent bookmark in my browser!
First I released the lock on the oven door hinge so that I could take the door off by lifting it up and out. Then it was just a matter of removing screws, replacing the hinges, and putting it back together. I did have to guess a little as I started removing screws as I wasn't sure exactly what to remove, but it became pretty self evident as I looked it over. Not as bad as I had expected.
SHUT OFF BREAKER FOR OVEN! pulled oven out to get at backside,removed 3 screws on back coverplate,removed 2 screws inside oven at sensor in top left corner of oven,disconnected plastic clip at back ,pulled old sensor through hole.replaced sensor with new in reverse order. 15minutes tops.
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
glass pane was cracked during the cleaning process
needed to completely dis assemble the oven door to get to the inner pane of glass...took some time...I was able to do it on my own...could possibly go a little quicker with two people for a few of the steps...but possible by one...then reinserted the glass pane...and then need to re assemble the door layer by layer...up and working again...would have cost several hundred dollars if need to call a repair person in...this way was the cost of the piece..less than $70 ... and my time...well worth it....thanks
Be prepaired to take the glass out. Unexpected, but not too hard. A right angle screw driver can be helpful for the bottom door. Takes some skill and patience. Good Luck! I am happy with the parts. Delivery time was quick.
The heating element for the oven section was luke warm even when the control was turned up high.
I wasn't sure if it was the heating element or the temperature probe not allowing the oven to go above 200 degrees so I ordered both from Selectparts. After receiving my replacement parts (in record time thank you) the oven element had a hidden slit on the underside near the connection. During its removal the element disintegrated at that point.
Since Maytag is very user friendly to maintain, it was a matter of removing the retaining nuts securing the element to the back of the oven, and resecuring after replacing with the new element. I did have to take the back panel off the oven to reattach the wiring to the element. This was necessary because while I was removing and replacing the element, the insulation was pulled through the access holes. I also replaced the temperature probe because I had already ordered it. This was easier to replace however and I did not encounter the isulation problem as I had when removing/replacing the element. I recommended your company to my friends and would definately order parts from you should I need to repair another appliance in the future. Thank you again.
My wife heard a loud surge when preheating the oven one day. When I restored power, the oven wouldn't heat and half of the oven display would not light. Broiler OK. Range top OK. The oven coil was electrically open after having melted through itself during the surge. I ordered a oven coil from PartSelect, based on model #. Installation was simple and only involved several easy to remove screws and a couple electrical terminal lugs. I replaced the coil but the oven would not heat beyond 100°F. I ordered a new oven display from PartSelect. PartSelect described what display series is required for a particular serial number. The first 2 #'s of the serial # are the display series required for the oven. My serial's first 2 numbers were 1 and 7, but PartSelect offered only a 10 or 12 series. I ordered a 12 series display and the part was identical. When I removed the faulty display, there were clearly burnt regions of the circuit card. Removal and installation of the display involved a nutdriver, philips screwdriver and circuit card plugs. I am not sure what caused the failure, the display or the element, but, in either case, I believe the cause is eliminated. The total repair costs were around $225 in parts. At the moment of failure, the oven was approximately 5 years old.
Stove top wouldn't come on. Oven couldn't go higher than low heat
Had a technician from Home Advisor to check the problem out with my Whirlpool Double oven(1 1/2 old). Paid $60 to find the problem. According to the technician problem was control board and cost of labor and parts $465.00 Jumped on Part Select website, placed a question with my stove problem through the chat. Immediately they answered my question and told me the problem was the Terminal Block. Cost of part and shipping $25.00. Replaced it myself and everything works fine. Thank you, Thank you Part Select for your help and honesty.
I took the oven door apart, pulled out the broken fragments of glass and replaced it with the new glass. I should have taken notes as I took the door apart because it was a bit tricky to remember how all the pieces fit back together.
I was very impressed with how quickly the parts were shipped and the quality of the packing materials to protect the glass as it was shipped.
Repair was very simple. Took the door apart in layers, replaced the glass and put everything else back. it took longer to clean the stove than it did to actually take it apart and put it back together. guess i didnt need to be that much of a clean freak!
