MDB6000AWW Maytag Dishwasher - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
diswasher leaked
-
tom from hicksville, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Soap dispenser failed to open
Opened circuit breaker feeding dishwasher Removed the 10 screws from the inside panel on the door. Unplugged two quick disconnect plugs. Removed the wax motor (actuating solenoid). Installed the new one from Parts Select. Reconnected the plugs. Replaced the cover and 10 screws. Turned the breaker on and ran a load of dishes. worked perfectly.
Parts Used:
-
Thomas C from Knoxville, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
Was this instruction helpful to you?
Thank you for voting!
water leak from disher on wooden floor
-
Charlotte from Carriere, MS
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Clip broke holding adjustable rack for dishes
-
Jennifer from Plattsburgh, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Dishwasher Leaking
Pulled the old gasket. Cleaned gasket channel very well. Centered middle of new gasket with the door latch. Then worked gasket in both directions to both ends. Closed the door and left with door tight for several hours to allow it to seat with the new gasket. When use was resumed the leak, at least to this point, has stopped.
Parts Used:
-
H Richard from Twinsburg, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers
Was this instruction helpful to you?
Thank you for voting!
upper dishrack had rusted and needed to be replaced
I found a short video on YouTube that showed me how easy it was to remove the old dishrack and install the new one. I would have never figured out how to get old diskrack out without watching short video clip. And, all I needed was my fingers to undo the end clips.
Parts Used:
-
James from Calabash, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
the right side folding shelf on the upper rack rusted through
I took the suggestion of a previous reviewer to bend the new part in. But instead of using pliers to remove the old part, I tried bending it to get it out. This was so that I could see how much force would be necessary to bend it without breaking it to get the new part in. I bent it in the middle and was able to get it unhooked from one side without too much force. To get the new piece in, first I made sure I had it lined up correctly. Then I inserted the circle over one of the side prongs to hold it and gently but firmly bent the piece in the middle until the circle on the other side could slip over the other prong. It was not bent enough to stay bent, just to compress it into the space and have it spring back to full length.
Parts Used:
-
Judith from Old Greenwich, CT
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
water leak - tub overflow
remove panel on front to acess float @ float switch.Remove phillips screw to float switch,remove palnut from float shaft with 5/16 nutdriver.Remove float from inside washer.Reinstall new parts reverse order.
Parts Used:
-
walter from salisbury, NC
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!