Quick Question!

Have you ever purchased from PartSelect.com before?

Models > MAH9700AWW > Instructions

MAH9700AWW Maytag Washer - Instructions

All installation instructions for MAH9700AWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MAH9700AWW
31-45 of 69
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Power Surge Disabled Washers Electronic Control Board

  • Customer: George from Salem, CT
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 7 people found this instruction helpful
The control board arrived the day after it was ordered which was a good sign of this stores devotion to customer service. The part that I received was an exact fit with no modifications or adapters required. One pleasant surprise was that it also came with a motion sensor which plugged directly into the control board and was hard mounted on the washers upper plate with existing hardware. This sensor completely eliminated the vibration issue we had with the washer since it's purchase and was a super simple install. As a matter of fact this entire install required nothing more than a philips screw driver and about twenty minutes of my time to plug in the harnesses and reinstall all of the fasteners ( along with the upper and rear panels to the appliance ). Nice product and a quick repair.

Main sping wore through Spring support bracket

  • Customer: Paul from Green Bay, WI, WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 3 of 4 people found this instruction helpful
In this model the 2 main springs hang from a bracket built into the top of the machines frame. For some reason one of the pring was installed without the protective plastic grommet (called the guide spring washer). The handened spring eventually wore through the softer metal bracket due to the vibration of the washer.
The purchsed plastic part fit into the bracket so firlmy that even with part of the bracket wore away it appears to be still strong wnough to support the weight of the tub. It has made it through 10 loads so far and it still working well.
Getting at the spring was easy but lifting the tub was heavy. Thanks - $4 part saved a $1000 washer.

Washing machine wouldn't run. Kept making buzzing sound and didn't show door latched.

  • Customer: Keith from Amherst, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 5 people found this instruction helpful
Removed the 3 screws that hold the bottom front panel in place. Removed the 3 screws that hold the door latch in place and pulled out on the bottom of the door which wasn't very much and slid the door latch out to get to the wire connections. Connected the wires to the new latch and pulled out bottom again and put the latch back into place and put the 3 screws back in. Note: make sure you unplug the washer so you don't have a chance to get shocked. Level of difficulty was pretty easy.

broken latch

  • Customer: Hector from Richmond Hill, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 1 of 3 people found this instruction helpful
Unplug machine,remove three screws that hold on top cover.
Unplug latch switch assembly,then open front door of washing machine, remove three screws which hold latch
switch. Install in reverse order.

Close quaters to work on

  • Customer: Lanny D. from Clarksville, TN
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 5 people found this instruction helpful
I had to pull the washer out from the wall. SInce it is in front of the door going out into the garage made it dificult getting tools. I had to lay on my side doubled up in order toget to the hose. I used a bit extention so that I could get the clamp loose. Cut the time in half by using a drill with a phillips head screw bit. The only real hard part was getting the new one up tight on the drain. Used a heavy duty screw driver to push it up so the clamp would bite.

OE error. All i read indicated the need for new sensor, but it did not correct the problem.

  • Customer: LISA from PRINCETON, WV
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 26 people found this instruction helpful
My husband simply removed the old sensor and put the new one in. It was not difficult.

shakining and moving

  • Customer: David from Manchester, NH
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Wrench set
  • 0 of 0 people found this instruction helpful
Installed dampners with a little trouble because of location on machine. But turned out not to be the problem. Machine still shakes and move. Looking for for another reason for shaking. Replacing dampners would be a "do it yourself project" for most people.

Washer flashed error code DL (door lock) and wouldn't start.

  • Customer: Marybeth from Warwick, RI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
We followed another very helpful repair story. Unplug machine. Unscrew top back screws, remove top of washer. Reach inside from the top in the front of the machine. Remove screws holding latch in place, unplug the three plugs attached to latch. Replace with new door latch, screw it in place, replug the three plugs, put top of machine back on, replace screws on back and your'e done! Works great! Job made easy thanks to others helpfulness!

Error code nD not draining

  • Customer: Daniel from New Milford, CT
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
I ordered the pump because we have 3 kids and laundry piles up. The pump was not the issue, because it would drain in rinse, but not during spin... The computer would have been a $330 part. Not sure the issue, but my wife wanted a new dryer so we replaced the washer at the same time. I didn't use the part. The website was really easy to order and it got here fast.

Door lever was broken

  • Customer: Karen from Cincinnati, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the broker door lever with screwdriver, installed the door lever with screwdriver. Took about 5 minutes.

impeller destroyed, over worked the pump motor and burned it out

  • Customer: Dora from West palm beach, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
this is a front load washer, removed a small access plate from the back of the washer, removed the old pump and install the new one

The message d5 was blinking

  • Customer: Betty from Diana, TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I had noticed the latch on door was split so I ordered the latch, but before I could put it on, the latch on the front of washer was locked. I then looked at the messages from others on this site for help. My daughter and I unscrewed the 2 screws on the top back, removed top, pulled the control panel up, unscrewed the front, unscrewed the 3 screws for latch, pulled old one out. I located the part, ordered it and got it in 2 days! Put new latch in and screwed everything back the way it was and in 15 minutes, the washer is running! (I am a woman too!)

Door latch/lock assembly needed replacement

  • Customer: Dee Earl from Pocatello, ID
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
The washer tech manual stated to: 1) remove the top, 2) control console, 3) front below the door (front load washer), 4) remove the retaining wire, 5) pull back the rubber bellows, 6) remove the three screws and remove the door latch/lock assembly. I discovered that steps 1 through 3 are not required to replace the assembly. Installation is the reverse of steps 4 through 6. That was easy. The difficult part was figuring out how to reset the pressure switch so the drain pump would not start every time you reconnected to the power supply (pressure switch thinks the washer still contains water). With the power disconnected, I disconnected the pressure switch from the central control unit. Then I reconnected the power supply and pressure switch. That reset the pressure switch solved the problem with the drain pump. Washer works fine now.

broken door frame and hinge holder

  • Customer: EARL from CHARLOTTE, NC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
found diagrham on line, located parts needed , orded,replaced when arrived a few days later.

No start Flashing Light

  • Customer: Tammy from Maplewood, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
This took ten minutes .... super easy .... DO IT YOURSELF!!!! About 75.00 with shipping ... can only imagine this woulkd have been 250 to 300 to have somebody com e onsite.
All Instructions for the MAH9700AWW
31-45 of 69