Models > MAH9700AWW > Instructions

MAH9700AWW Maytag Washer - Instructions

All installation instructions for MAH9700AWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MAH9700AWW
16-30 of 65
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Blades of impeller of drainage pump broken.

  • Customer: Mike from Big Canoe GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 9 of 12 people found this instruction helpful
Unplug the washer and remove the back cover plate of the washer. Have old towels and a small receptacle to catch water from the lines. Drain the pump and drainage lines. Remove the two hose clamps and remove the connecting hoses. Disconnect the electrical connection from the pump (small plug connection). Undo the three mounting bolts holding the mounting plate for the pump. Remove the pump from the plate and install the new part. Remount the mounting plate, attach the hoses and clamps. Reattach the electrical connection and the back plate to the washer. Plug that baby in and works like a champ!

Because of sand in my well water,the valve quit working properly and water would run constantly

  • Customer: Robert from Monticello GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 7 people found this instruction helpful
I removed two screws on the back of the washer,removed the top of the washer unclipped three plastic wiring clips, removed two screws holding the valve in place.replaced valve and replaced wires and top of washer. Total time about 15 minutes

door latch error code

  • Customer: Gary from Sonoma CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 13 people found this instruction helpful
removed all the panels to change the door latch switch
plug in three plugs ...works great
Thank you

Water was sprating all over the inside of wash machine onto the circuit board.

  • Customer: William from Marion WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 7 people found this instruction helpful
I took the two screws off the back that holds the top down, lifted it , then pulled it back to remove. After this was removed, there were two more screws holding down the assy-s housing and drawer. First remove drawer where you add the soap and softners. Then I pulled that back and the assy-s housing drawer just snaps onto the housing. I pulled the drawer off, then I took the four hoses that are connected to the back and put on the new one in their respected spot. I snapped it back on and reassembled. You don't need a maytag repair man to do this job.

No Power to the machine after power outage

  • Customer: Grant from North Fork CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set, Wrench(Adjustable)
  • 7 of 11 people found this instruction helpful
I removed two screws that held the top on,and removed top. I then rermoved screws that held control module in place. Disconnected the wires. I then placed new module in place,and plugged in wires. I also added a vibration sensor, that came with the new part. Plugged in machine ,and tested it as per the instructions. Everything worked as it should. Fixed the problem

the door fell off the machine. an entire cover had to be replaced because of plastic , plastic plastic. It would seem smart to use something a bit more substantial to screw the door to.

  • Customer: brad from cody WY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 5 people found this instruction helpful
take the cover off and put the new one on..See you in another four years plastic again!!!!

FOLLOWING THE INSTRUCTIONS OF THE REPAIR MANUEL,

  • Customer: gerard from arvada CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 4 of 5 people found this instruction helpful
FIRST I REMOVED THE RETAINER RING AND THEN PULLED BACK ENOUGH OF THE BOOT TO GET THE DOOR SWITCH OUT AND PLUGGED IN THE NEW SWITCH PUT THE RETAINER RING BACK ON AND IT WAS FINISHED. WITH OUT THE REPAIR BOOK I WOULD HAVE BEEN LOST ON HOW TO DO THE JOB.

Chewed up door latch

  • Customer: Jody from Lafayette CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 8 people found this instruction helpful
The dog ate the door latch so I ordered a new one. All I had to do was unscrew the old one, remove, and screw in the new one. Super easy. Took longer to find the screwdriver than it did to make the repair.

The washer was unable to run without door locking

  • Customer: MICHAEL from DERIDDER LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 6 people found this instruction helpful
Removed the washer tub gasket and then removed the door part that I order . It was real easy to replace it and the tub gasket . Took about 8 min to complete everything .

Door hangs down so you have to lift it when closing. Eventually the whole latch mechanism broke.

  • Customer: Brenda from Bodega Bay CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 15 people found this instruction helpful
Pull washer away from wall and find two screws in back next to top edge. Undo and pull top of machine off (lip on fron edge under face cover). reach down and unplug three plugs on door latch small one on top, biggest on bottom. Unscrew the three screw holding the latch on the front of the machine, take out the old and put in the new. Note, I pluged in the plugs before screwing the new one in place, and that might be easier. Put the top back on.
I couldn't find any way to adjust the door, so you still have to lift it up when closing.

Broken Glass

  • Customer: Clint from Arlington WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
(1) Remove all screws keeping them organized as a set,(some are larger than others,for the glass frame only. After all screws are removed remove frame from the door.(2) Remove old glass and replace with the new one and put it all ack together.

Door lock would not open.

  • Customer: JOHN from LUCK WI
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 4 of 7 people found this instruction helpful
Took off top. Removed front control panel.Removed top screws on front door panel,then I had access to door lock for removal.Had to replace door latch also as this was broken while trying to close door before we noticed the door lock was not working.

door would not latch , and lights on front just flashed

  • Customer: FRANCIS from leesburg FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 7 people found this instruction helpful
1)I removed the bottom front panel,reached up the right side of the machine and pulled the manual release on the bottom of the latching mechanism.2)I then removed the top to the machine in order to gain access to the latch. 3)I removed three electrical connectors then the three mounting screws using a #15 Torx driver. I then reversed the reverse procedure to install the new latch. total time to do the job was less than half an hour. Machine works OK.

POWER SURGE DISABLED WASHERS ELECTRONIC CONTROL BOARD

  • Customer: George from Salem CT
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 6 people found this instruction helpful
THE CONTROL BOARD ARRIVED THE DAY AFTER IT WAS ORDERED WHICH WAS A GOOD SIGN OF THIS STORES DEVOTION TO CUSTOMER SERVICE. THE PART THAT i RECEIVED WAS AN EXACT FIT WITH NO MODIFICATIONS OR ADAPTERS REQUIRED. ONE PLEASANT SURPRISE WAS THAT IT ALSO CAME WITH A MOTION SENSOR WHICH PLUGGED DIRECTLY INTO THE CONTROL BOARD AND WAS HARD MOUNTED ON THE WASHERS UPPER PLATE WITH EXISTING HARDWARE. THIS SENSOR COMPLETELY ELIMINATED THE VIBRATION ISSUE WE HAD WITH THE WASHER SINCE IT'S PURCHASE AND WAS A SUPER SIMPLE INSTALL. AS A MATTER OF FACT THIS ENTIRE INSTALL REQUIRED NOTHING MORE THAN A PHILIPS SCREW DRIVER AND ABOUT TWENTY MINUTES OF MY TIME TO PLUG IN THE HARNESSES AND REINSTALL ALL OF THE FASTENERS ( ALONG WITH THE UPPER AND REAR PANELS TO THE APPLIANCE ). NICE PRODUCT AND A QUICK REPAIR.

Door latch would not lock

  • Customer: William from Victorville CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 3 people found this instruction helpful
Removed 2 screws from rear of top that hold top of washer in place, lifted top at the rear and slid it back then lifted it off. Removed the three wiring harnesses from old switch, removed the three screws holding switch in place, theses are accessed from the door opening. removed the two lower screws first and held the switch from the top while removing the last screw. Placed new switch in place and started the top screw by hand followed by hand starting the remaining two screws, tightened screws with phillips screw driver, reconnected the three harnesses, reinstalled the top and secured with the two screws. Door locks and unlocks as it is supposed to.
All Instructions for the MAH9700AWW
16-30 of 65