MAH6500AWW Maytag Washer - Instructions

followed the diagnostics instruction in the Maytag Owners booklet which pointed to the Motor Control Assembly.
PartSelect was a very good choice for securing the part.

On the Maytag front load washer, we found the easiest way was to unscrew and lift the top of the washer up, then take off the door, and front panel. Removing the old seal (moldy) was easy, but to replace the new one you need to see what you are doing. (Reaching up blindly to slip the new seal around AND connect the spring, is near impossible.) It was not hard to do...IF you can see what you are doing. You need access to attach the drain tube, make sure the gasket is slid in place (with notches in line with openings) slip the cable around and attach the spring. Everything is easy IF you can see what you are doing (and a little muscle to pull the spring and connect it).

followed the approach on fixya.com. when installing new boot and cable loop, found it easier to remove drum cover from machine (held on with simple clips). Then you can install boot onto the cover and the door frame. Putting everything back in machine and re-attaching the various braces took only a couple of minutes.

I opened the door on the washer,and pushed on inner tub upward.it moved about 1 inch and the I knew tub bearings where shot .So I removed all components and repaced the outer tub with new bearing pack.. NOTE... Not an easy repair..but when i finished i had no probems with water leakage.ALL GOOD.

The boot tear looked the easiest but turned out to be the toughest.
After removing the door 2 screws, and finding the opposing two screws I removed the face panel.
Removed the two screws located under the face panel directly under the washer top surface. This allows access to the top of the washer. A wire clamp held with a spring holds the boot in place. Remove the spring or roll it over the edge of the front of the washer tub. Two screws hold the sub-face panel onto the carcass of the washer. remove these. The boot comes out easily. Follow the reverse to reinstall. This may sound easy..its not! The problem lies in the wire and spring arrangement. You must hold both ends of the cable in place near the washer drum taughtly but not too tight or the pressure will cause the boot to edge over the washer tub. It became so bad I consulted a Maytag repair guy. He said we use two pair of needle nosed pliers. Tried that caused banged up knuckles and lots of bad words. I made a tool that operates like a pair of scissors holding the wire on one side and the spring on the other. If you are interested you can track me down and I will tell you how. The softener still doesn't work. Drat. I will have to replace the computer next. OUCH

Opened a small door in the rear of the washer and loosen the two braces with a screw driver and pulled the old hose and replaced with the new hose replace the door and that was all.

The machine comes quickest appart with a cordless screwgun and a #2 Phillips.

To unhook the wire with spring it is easiest to use a needle nose plier and make a hook from a coat hanger or use a paint can opener.

Pay attention when yo line up the boot with the flange in the back, that the rectagular protrusions line up with the holes in the flange. You may have to stretch the boot a bit and push it all the way in with a dull tool.

Get someone to help you put the wire back on if you want to do it fast and easy. Otherwise hook it on the spring and get the pliers on the loop on the other side and pull it together, torquing the wire back so that it does not make the boot slip fo the flange.

Done

I ordered the grommet and inner door on a Tuesday and had both parts at my door step the following day. Including shipping it was only $64.00. With only a screwdriver in hand and 45 minutes of time I removed four screws to take the entire door off. I then removed the inner door and vent tube and grommet (very easy). After placing the new grommet into the new inner door I inserted the vent tube and screwed everything back together.
The repair man would have charged $90 for the labor and the parts which he would have had to order would have been extra.

Removed old broken plastic grommet's and installed two new plastic grommet's. Attached new baffle using old screws. Used a short piece of picture frame wire to install the two new grommets by fishing them into place with out removing the washer drum.

I removed the screws around the front door. Then removed the front face. I removed the bolts holding the top down at front top corners. I removed the detergent dispensor. Next I removed the spring and hold down cable. I then pulled out the old boot. I then, with the help of my son, pulled the new boot around the drum. Then attached the cable and spring. Next pushed the boot into the front retainer. I then put the dispenser in and the front back on. Good as new. It was not hard as long as you have someone to help with pushing the boot around.

Removed old motor installed new motor.

Removed four screws using elctric srew driver.
Pulled the old lid out and installed the new one.

Remove the ten screws to the inner door to remove it. There are components in the inner door that we didn't think would be there. Take out the components on the inside of the inner door. The areas where the ten screws go in have the small metal plates that we needed to be transferred to the new inner door. Otherwise the screws will not fit. It flips out. That's the part that took us a while to figure out but it came out easily. The other parts snaps on and off after the two screws are removed.

Just remember what you removed and where it should go. It takes two people to do the work.

First ya have to find the problem that takes time.
Pulled the front off via the four screws, two on the door and two on the opp side. Removed the two top hold down brackets that hold the top on (on the front), popped out the four screws for the detergent and the top hinged up, The hose was right there. Removed the two hose clamps, found the crack ordered if from you guys.(very fast) slapped it in and put a load in.

got instructions off internet from others who did same repair; after taking inner basket out, used drift to remove outer bearing; seal was difficult to remove but used drift to force innner bearing into seal and seal popped out. had help reinstalling inner basket into outer basket.