All Installation Instructions for M120

Broken fan axial blade

Unscrewed the unit from the exterior case pulled out the unit unscrewed the 4 screw that hold the fan shroud carefully unscrewed the coil pulled back unclipped the axial fan clip gentlyhit with rubber mallet replacement of new fan replaced clip
15 minutes best investment of 20 bucks as apposed to 400 $

Parts Used:

FAN,AXIAL

John from HARLINGEN, TX
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

6 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

light bulb in water ice freezer door went bad

I didn't. Don't know how to get to light bulb to change it for this specific model

Parts Used:

Light Bulb - 40W

Carl from RIVERSIDE, CA
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
Tools:
Screw drivers

7 of 13 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Replacing the bulb in the freezer side

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Parts Used:

Light Bulb - 40W

Yafa (and David) from Bothell, WA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

5 of 10 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

window a/x unit fan broke

took apart the fan housing and replaced the fan saving me hundreds of dollars from buying a new unit

Parts Used:

FAN,AXIAL

margaret from CARRIERE, MS
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers

6 of 14 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Motor mount broke due to imbalance caused by mud dobber nests.

Pulled PTAC out of wall sleeve, unhook wire harness from control area, remove condenser shroud and motor and fan blade all at the same time. Replaced motor bracket and re-installed in reverse order.

Parts Used:

BRACKET,MOTOR

Travis from LOUISVILLE, IL
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

oven light burnt out

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

Parts Used:

Light Bulb - 40W

William from Schwenksville, PA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins

3 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

burned oven bulb

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

Parts Used:

Light Bulb - 40W

Ivanka from Atlantra, GA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

3 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

light bulb went out in my oven

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

Parts Used:

Light Bulb - 40W

Janet from Ada, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Capacitor went out

Unplugged and replugged everything and it worked very easy job thank you

Parts Used:

CAPACITOR,ELECTRIC APPLI

Al from CROSS PLAINS, TX
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

1 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

replaced oven lightbulb

very easy

Parts Used:

Light Bulb - 40W

peggy ann from forest city, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Light burned out in upper oven

Screwed in light bulb and glass protector

Parts Used:

Light Bulb - 40W

Shirley from Las Vegas, NV
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Bulb Replacement

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

Parts Used:

Light Bulb - 40W

Judith from Phoenix, AZ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

fan had stripped out and was replacing.

very tight working situations. made a mistake with a delicate piece of the fan and broke it and that rendered the part unuseful. Since I broke it I considered it to be my fault and just threw it away. Ordered another from another company hoping that just maybe it would be more durable. It arrived in only 4 days. Yours took well over a week to arrive. Thanks for asking for my experience.

Parts Used: