LW8463W2 Amana Washer - Instructions

I purchsaed a new water valve and it was very easy to install. I hate to do thos kind of repair but it went very smooth. Took maybe a half hour, and now it works like new.

Removed the front panel, could see water leaking from the tub area near the shaft in the center of the machine. Dripping out once the water level reached the hub. Swing the top up, remove the large plastic ring at top of tub. remove the top of the agitor, pulls off easily. Remove the agitator with a firm pull up, not as easy but does come off. Removed the 4 bolt holding the tub. 2 broke off, but not to worry, the new kit has a complete hub. Pulled off the bell seal, pry up. Used an impact gun with 1-1/2" socket to remove the nut. The hub was frozen to the shaft. Tried a puller but ended up breaking the hub. I finally cut it off in pieces and pryed it off (the hardest part of job). Cleaned up the spline with a small file and patience. Installed the new seal kit. Ended up buying the M800 3M sealant on line. I went this far, another $40 for that. Fitted it all back up per instructions. No leaks. All good.

Put new motor in, and it did the same thing as old motor. Obviously, motor wasn't the problem. Looking for answers on what the problem could be.

remove motor and pump togather 4 bolts holding unhook two hose unplug electrial connector and slide out remove 3 screws holding pump to motor be aware of direction belt from moter to tub then place new pump back at same location as old pump replace motor with pump attached back to same location as begfor

Unplug the electrical cord. Remove the front cover with two screws at the bottom. Unhook the front two springs on the tub that secure it to the floor of the machine. Tilt the tub back as far as possible. Remove the electrical connector to the motor at the motor with the plastic tab release. Remove the four screws that attach the motor mount to the floor of the washer. Unhook the two hoses that attach to the pump on the motor bottom. Catch the water in a towel or in a flat tray. Unloop the belt from around the pulley on the bottom of the washer tub shaft and remove the motor, pump and belt as a unit. Remove the brake pads by removing the single bolt atop each one and pull it out of the machine. This will take the longest amount of time. You will have trouble getting the new pads in position, especially the one at the back. You many need to gently spread the brake disks to allow the pads to enter using a padded screw driver. Lightly lubricate the new brake pads before installing with silicone grease and replace the bolt and grommet with the new ones provided on each. Using a torx screwdriver, remove the pump from the motor and discard the worn belt. Remove the idler pulley using snap ring pliers and replace with a new one. Install the new belt and idler. Replace the pump with a new one, or reuse the old one if it seems in good repair and is not too old (mine was 15 years old--I replaced it). Remount the motor, pulley and belt on the machine and secure with 4 bolts--loop the belt around the main pulley on tub shaft. Reattach the hoses to the pump. Reconnect the electrical supply to the motor. Rehook the two spring to the front of the tub. Plug the washer back into the wall outlet. Pour in a couple of gallons of water into the tub before starting to ensure that the pump does not operate in a dry condition. Start and test operation. Be Happy. Wash hands and have a cold one.

You tubed this procedure and it took 20 min.

The new hose was exactly like the one I removed. It was simply a matter of putting the new hose through the back, replacing the hose clamp, take the piece off the old hose that makes the bend in the hose to go in the wall drain. Replace the lower front panel with two screws and I was done.

After pulling front lower panel off, disconnected idler pulley spring and left side tub stabilizer spring to allow room to get motor out the front. Took belt off transmision pulley, unbolted 4 motor mount bolts, dropped the motor/pump assembly down and disconnected the electrical plug (motor). Took motor/pump assembly out, flipped it over, unbolted 3 pump bolts to remove old pump, which came right off. Then reversed the whole process. Pretty straightforward, just time.

Turned off water & unpluged ac power. Removed 2 screws on front panel. Removed panel. Found peices of V belt. Removed 4 screws from electric motor which allowed the belt to come out. Ordered new belt on line. Received the item in one day. Reversed the above sequence above. Now the washer is running as good as new.

Researched the common problem with "dryer not turning on", and tested the top three problems. Removed the dryer front casing and door, unbolted front dryer plate. Used a volt meter on two of the temp gauges, which were fine. Removed the upper back plate of the dryer to the wiring for the knobs and buttons. Used the volt meter on the dryer start button, which was also fine. Went back around to the front and removed the door switch. Tested it with the volt meter and bingo. Replaced that part, dryer works like normal.

My Amana washing machine burned up a second belt in about three weeks. Prior to that, the spin cycle was very loud. Online research revealed the problem was most likely the hub bearing. I ordered a new bearing, belt and hub and seal kit. The repair is a difficult one as the parts have been on the tranmission shaft many years with the mounting corrosion and mineral build up. I was able to pull the agitator off with no problem. The drive bell would have been easier to pull had I used a gear puller but did not own one. I use two crow bars to lift it off the shaft and I knew I'd be replacing it anyway so was not concerned about damaging it although I didn't. The most difficult part to remove was the large hex nut. I didn't want to purchase the tool to remove it so I used an open end adjustable wrench adn a hammer to remove it. However it took many hours of soaking the nut in sprayed on WD-40 to loosen it. For a while I thought it wasn't going to budge. Oh and btw, the nut comes off counterclockwise on this model. This is important. Other makes of washers have left handed threads, requiring clockwise removal, but this one does not. The hub assembly was pulled using the crow bar method. Again, it was going to be replaced anyway. The lint filter was cleaned and reused. The remainder of the dissassembly went OK using the directions in the repair manual. http://www.scribd.com/doc/8677902/Amana-Top-Load-Washer-Service-Manual. Reassembly went fine using the repair manual accept that the new drive bell was much more difficult to drive onto the shaft than I thought it would be. I eventually got it on using my shop vac rigid tube to go around it and hammering on a block of wood placed on top of it. I also used this shop vac tube to seat the seal that goes on the shaft just before the drive bell. It was the perfect tool for it as I wasn't going to purchase the special tool suggested in the repair manual. I'd already purchased $185 in parts. The kits come with grease but not the anti seizure compound or the industrial sealant needed. The anti seisure compound can be purchased from an auto parts store. It's not expensive. The industrial sealant is expensive. After researching what it was and why it was needed, I took a chance on silicone sealant. I'm not suggesting it is a good substitute but my washer has not leaked after 5 loads. Plus the sealant is really a backup to the main seal that goes on the transmission shaft before the hub assembly. But I'm pleased overall with the parts and accompanying directions and the washer is working great, spinning quietly. This is not an easy repair. It takes patience and a place to work on it. Frankly, with other things to do as well as go to work, it took me four days to complete, mostly due to the difficulty in removing the large hex nut. It might be worth investing in the removal tool if you're unsuccessful using home tools. Good luck.

The hardest part was removing the tub from washer by myself. I simply removed the bolts holding the sides to the bottom of the unit and lifted it straight off. Be careful when you remove the springs from the drum so they don't spring back and puncture the drain line. Thank you RTV gasket maker. Once the drum was free from the base, i tilted the drum back exposing the pump housing. I used a pair of pliers to remove both drain lines then removed the 3 hex screws freeing the pump. I had no problem removing it from the motor shaft, it slipped right off. I put everything back together as easily as it came apart.

Removed the back plate. Disconnected the inside water hose. Unplugged the electrical contacts. Pulled out the old valve, connected the water hoses to the valve, plugged in the electrical contacts, reconnected the inside water hose, and put the plate back on the washer. The hardest part was putting the plate back on the washer. This entire repair would have been exceptionally easy except that I had to sit on top of the washer and hang upside down to do the repair due to the extremely small space the washer was in.