Models > LNC6760B71 > Instructions

LNC6760B71 Admiral Washer - Instructions

All installation instructions for LNC6760B71 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the LNC6760B71
361-365 of 365
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Lid hinge on right side broken, lid hinge pin broken on left side

  • Customer: Layne from Waynesboro VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Watched video , after that there was no problem, really easy.

washing machine shakes and moves during spin cycle

  • Customer: Erich from Sheffield Village OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
Had no problems taking machine apart following online instructions. At first couldn't find snubber ring because it was completely worn away. Once found it was very easy to replace. Only problem with putting back together was getting the first spring back on, after that it was a breeze. Machine up and running.

washer danced around in spin cycle

  • Customer: Donald from Rapid City SD
  • Difficulty: Very Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Socket set
  • 0 of 0 people found this instruction helpful
I would not recommend trying this without the spring removal & re-install tool. Very difficult to impossible to remove the springs with pliers. Not meant for novice handy persons.

Won't Agitate, Won't Spin, Jumping around, squealing in spin cycle, abrupt stop

  • Customer: Gina from Los Angeles CA
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Washer was jumping around in the spin cycle to the point that it disengaged the water fill level hose which in turn caused it to overflow. I fixed the hose but almost immediateley it stopped spiining or agitating. I looked online to find that the jumping around was most likely the snubber ring ... the hard stop and squeal most likely the Brake Stator ... the no agitaion or spin was likeley the thrust bearing. I ordered the parts and were received in a couple of days ... by the time they came I had already torn apart everything and was just waiting on parts for reassembly. The instructions were concise and complete but I did benefit from watching a YouTube video on the repair. All the parts went together just like they were supposed to even with my limited mechanical skills. All I really used was a small socket set, a couple of screw drivers and a pair of pliers. Taking the Brake assembply is dangerous but can be done with no special tools if you buy a couple of 2 inch 10-24 screws to replace two of the short ones and then back them out slowly (look for a youtube video on this procedure EASY!) ... took me a couple of hours but any one who has used a screw driver more than once could probably do it in under an hour. Washer now running like new ... No Jumping!!! People at Parts Select were Great!!! BTW ... So that the springs would be easier to re-install, I stuck about $50 of quarteres between the coils before removing ... worked Great!

Motor hummed and did not operate.

  • Customer: Cheri from Crowley TX
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
1.Removed front panel to access the motor. 2.Tilted the washing machine onto it's back, in order to remove the belt. 3. Unpluged motor wiring and removed the old motor and mounting plate.
All Instructions for the LNC6760B71
361-365 of 365