All Installation Instructions for Whirlpool Dryer LGR4434AQ1

Dryer wouldn't start

Watched the tutorial online. Took the back off- replaced the fuse. Put the back on . It was extremely easy !!

Parts Used:

Dryer Thermal Fuse

Rhonda from Oconomowoc, WI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Thank you for voting!

Replaced Belt

The online vidio was very helpfull

Parts Used:

Multi Rib Belt - 92-1/4"

MARCUS from MACON, GA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

the dump would not stop running.

Replace the switch in diagram #4.

Parts Used:

Dryer Thermal Fuse

modean from Clermont, FL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

dryer tub drive belt broke

Unplugged the power cord. Removed two screws on lint vent , used putty knife to release clips to raise top at front of unit. Disconnected the plug from front door switch. Laid dryer on its back. Removed two screws to remove front including the door. Vacuumed lint from inside unit. Installed belt temporarily using two pieces of masking tape to hold it in place while properly routing the belt. Gave the tub a full turn to insure alignment.. Reinstalled the front of unit with the two screws. Righted the unit and snapped down the top. Replaced the two lint vent screws. Plugged it back in and done! Piece of cake!

Parts Used:

Multi Rib Belt - 92-1/4"

Ray from Salisbury, NC
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Washer overflowed

Once I watched a YouTube video showing me how to do the job I ordered the part from you. Am so impressed with your fast shipping and best prices via the Internet. Thank you SO much! The water level switch was easy to install, it ws getting the cover on the washer back on that was hard for me since I am 68 yrs old and have a bad knee. Its why it took me two hours to do what most people could do in 20 minutes.

Parts Used:

Leveling Foot

Beth from Valley Springs, CA
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Dryer wouldn't turn on

When the part came in. I unplugged the dryer. Pulled it away from the wall and took the back off. I pulled the wires off the old fuse and plugged them in the new fuse, then unscrewed the on nut that held the old fuse. Then slid the new one in and put the nut back on. Plugged the dryer in and it worked. So I unplugged the dryer and put the back on.

Parts Used:

Dryer Thermal Fuse

pamela from ocean springs, MS
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Noisy tumbler & worn lint trap seal

Followed procedures in Parts Select web site video

Parts Used:

Rear Drum Support Roller Kit

Lint Trap Housing Seal

Pedro from Brunswick, GA
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Dryer would run, but not heat

Removed the back panel, found the fuse and replaced it. Easiest thing I've ever done! I was expecting it not to be the problem, but I started with the "most common" issue via the website. Voila...it was the problem!

Parts Used:

Dryer Thermal Fuse