LFFU1424DW9 Frigidaire Freezer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
handle broke at the attachment point on the door
removed two pieces of trim.....removed four screws of old handle.....replaced with new handle....replaced screws.....replaced trim pieces
Parts Used:
-
Dylan from Celina, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
3 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Getting frost build up on the inside at the top of the door .
removed door and took all the screws out of the inside door rack. removed old door seal . replaced door seal and made sure that the seal fit around and door rack fit into the groove then replaced all screws and tightened choosing random sections to tighten .replaced the door plugged back in wires that I removed and replaced door hinge screws . Shut door and checked sealing 2 hours later .Complete seal .
Parts Used:
-
Gene from VICTORVILLE, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door handle broke off of the refrigerator
Was able to order the handle and screw it on the refrigerator using the screws from the original handle in about 10 to 15 minutes.
Parts Used:
-
Edith from FORT WAYNE, IN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Freezer was frosting too much for air getting in the side of freezer gasket seal.
Loosen screws, removed old gasket seal, replace with new gasket (nice to use 2 sets of hands) and re screwed. Used hairdryer to heat up and fluff out a spot that wasnt seal all the way. Pretty simplementation to do.
Parts Used:
-
Mary from LE ROY, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
door handle broke (3rd one) poor design
-
Edward from GRAND FORKS, ND
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Handle broke loose
Just screwed in the new handle. Must keep the original trim pieces that slide on the top and bottom, or order new ones if needed.
Parts Used:
-
Richard from SWAMPSCOTT, MA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Just lost key
-
Toni from Little Rock, AR
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
2 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken door handle
remove cover plates slide off , exposes screws holding handle on to the door remove screws ( 4) 2on top 2 on bottom replace with new handle in reverse order of disassembly slide cover plates back on , job complete .
Parts Used:
-
Rick from MENDON, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken door handle
-
Russell from BAYVILLE, NJ
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Condensation around inside the door
Unscrew all the fasteners from the door inner cover from the bottom to top to hold it in position, got rid of the old gasket.
I Cleaned all and install the new gastket into the door inner cover. then reintalled cover to the starting from the top to bottom to hold it in place.
this is a one man job but with two will be easer
I Cleaned all and install the new gastket into the door inner cover. then reintalled cover to the starting from the top to bottom to hold it in place.
this is a one man job but with two will be easer
Parts Used:
-
Sixto from MIAMI, FL
-
Difficulty Level:Very Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old gasket was broken
Removed old gasket, then installed new gasket. Make sure to allow new gasket to set out for a few days prior to installing to get all wrinkles out, use a heat gun after installing to make gasket shape to freezer door.
Parts Used:
-
Henry from BYRON, GA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Freezer wouldn’t turn on.
Put the new temperature control unit in plugged freezer back in and immediately turned on. Very simple repair. Saved a lot of money not having to purchase new or call a repair shop.
Parts Used:
-
Robert from HARDING, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Stop basket and right side shelf support were broken.
Used needle nosed pliers to twist and pull out remainder of broken parts (regular pliers would work, fingers might). Used fingers to insert replacements. So, simple, so glad I did it!
Parts Used:
-
Gregory from NEW ORLEANS, LA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door handle broke off
-
Rosemary from LEXINGTON, KY
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven not reaching temperature
Using the socket wrench, I removed the old element from the oven wall attached by two hexagonal screws. I then removed the electrical attachment to the oven using a Philips head screw driver. Replaced the element with the new one and reversed the process. The oven works like new!
Parts Used:
-
Andrea from MANLIUS, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers, Socket set
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!