LER3330AAZ Admiral Range - Instructions

The thermocouple was suspect. It should be super easy- two screws, but the wiring harness would not pull through on my oven. I confirmed the procedure with the PartSelect video which is good. The harness was caught and broke so I had to pull the oven out partially to get to the harness. The sensor did check bad on the multimeter (resistance too high- Google it, I did) so I ordered the part. Once the new part was installed the oven still did not function. So I had to get busy with the multimeter and pull the oven again. On the back of my oven near the wire to the bake element is a Hi Limit Switch which cuts off the bake element if the outside of the oven gets above the preset temperature. Mine was cracked and faulty and had to be replaced. The oven works great now.

Remove 2 screws in upper left corner of stove holding sensor in place. Pull sensor out and disconnect plastic electrical connector. Select appropriate adapter (both styles provided with new part) & reinstall. Power up stove and select bake on control unit to test. Works like a charm!

Simply remove the two screws in the back and carefully work the element out taking care not to pull the wires off. I left the oven door on which made access somewhat awkward reaching in. Remove wire clips and install new element in reverse. So easy even a caveman could do it.

I removed the broken hinge and installed the new one, however the oven door didn't stay ajar but dropped open fast. So I took the old spring and installed it on the new hinge and it was improved. It just took a screwdriver.

I removed the old thermostat and replaced it with the new one using the supplied wiring adapter for my model of range. Parts Select made this an easy project. Thanksyou

unplugged the oven from the 220 volt receptacle. Removed the wire shelves. Unscrewed the two screws holding element to rear of oven. (I didn't know at this point to pull the wires through from the back so I took the back panel of the oven off and unplugged the connectors from the rear). Measured the defective element, ordered, and two days later I reversed the process when the package arrived in the mail. . quite simple. I love it when I can fix something myself. And by fixing, I actually mean "replacing".

Followed directions as supplied. New part did not work, so it must be in the control unit which is no longer available. So time for a new range.

followed you tube instructions. Very helpful feature. thanks

Remove both oven racks. Remove the screw that is on each side of the element holding it in. Pull the element out and disconnect the wire on each side of the element.Remove the bad element and replace it with the new element. Connect the wires to the new element and gently push the element back into place. Put the screws back into place and tighten. Replace the oven racks into oven. Turn oven onand verify that the element is heating. Repair is comlete.

Cut power to range in breaker panel. Then removed two screws (1/4" nutdriver) or phillips head just under top in front. No need to move range out from wall. Once those two screws were out, I lifted the top carefully (since wires are attached to back of range) and propped it up with a piece of spare lumber I had lying around. Then removed two screws holding right rear burner, and doing one wire at a time, pulled the wires from bad burner and reattached wires to new burner. Oh, I did need some pliers to pull the wires from the old burner; they were on real tight. ALSO, the old burner had a series of numbers around it. I quickly learned that these helped you line up the burner correctly. So I noted the numbers with the screw holes in the old burner and made sure I used the same number holes in the new burner. Once new wires were attached, I attached the new burner, aligning the same hole numbers as the removed burner, and everything lined up perfectly. Two screws were inserted to hold the burner. I lowered the top and reinserted the two screws under the front of the top and I was done. Total time was about 13 to 14 minutes. Honestly, very easy. Plus prior to me taking on the project, I had called a Maytag repair shop, who said their fee was $99, plus parts, plus any extra time required for labor, but the latter was not likely something that typically occured.

Turned off Power to oven, flipped breaker. Unscrewed two screws, removed old burner, inserted new burner, screwed in. Turned breaker back on.

Removed stove from slot in wall. Bent rear left leg would not unscrew due to bent metal bracket. Used hacksaw to cut out leg, then straightened metal bracket with small hammer and was able to screw new leg in and adjust height by using level on stove before reinserting stove its slot. Recheck level after pushing back in place and adjust front legs if necessary. If not for bent metal receiving bracket, would have taken much less time. Still easy tho. R'cvd part in two days. Very quick.