Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
There was no problem
I simply had to hook up the power cord to the dishwasher so i could plug it into the outlet rather than direct wire the appliance. Everything went very smoothly. Everything needed for installation other than tools was provided. Easy to follow instructions if you know a little about electrical wiring.
Installed pump kit. Was surprised the kit seemed different( some parts changed or deleted. Instructed to discard old parts and follow with new configuration. Reassembled and tried t fin it works fine now. Thank you so much
Dishwasher simply stopped during operation for no apparent reason.
Removed the inner door panel and then the circuit board protective cover (which just snaps in). Fuse assembly is readily accessible and just snaps in. The wires are attached with spade lugs using existing wiring. No wiring modificatins needed,
The # 6 flexrow got wobbly and couldn't hold the dinner plates in line...then it just broke in half
DEFINITELY 5***** Stars The piece arrived, and my husband was able to pop out the old flexrow and pop in the new one.....took less than one minute. Voila...back in business again.
We had just made the (big) decision to not renew the warranty. The dish washer is 10 1/2 years old, and we figured we'd cross our fingers...never having a problem with it. A week later the flexrow broke. I called KitchenAide...they would/could send an entire bottom rack for $135.00. I found PartSelect, easily found the diagram and correct part, and for less than $30.00 we ordered it and it arrived at our front door within 48 hours. You can't beat that for quality and fast service. Thank you PartSelect. Larry & Nancy Lukunich Simi Valley, CA
removed two hose clamps and old hose. slid new hose on existing fittings on dishwasher drain and disposal and tightened hose clamps. Turned it on for test run.
broken clips that hold up vertical dishwasher racks.
Very easy to snap in. I would recommend to make them more slippery to snap in. Maybe use a little soap or place them in hot water before you place them on dishwasher tray.
One of the springs that support the down-swinging door
1) Removed the two panels below the door. 2) Unscrewed the two screws holding the dishwasher to the upper cabinet facing. 3) Pulled dishwasher out 6-8 inches to gain access to springs located on the side. 4) Removed the broken spring. 5) Attached the new spring. 6) Openned and closed the door to make sure spring was tight enough. 7) Pushed dishwasher back in. 8) Rescrewed cabinet facing screws 9) Rescrewed floor panels.
Only problem was with ordering ... PartSelect part number is different than the FSP-Whirlpool part number. PartSelect should provide a cross-reference table if there is a difference between OEM number and PartSelect number.
Prongs on Upper and Lower Dish racks were rusted and broken.
I ordered the upper and lower rack replacements PLUS additional wheels and other attachments because I could not tell from the schematic on the website whether or not the smaller pieces came with the rack.
As it turned out, the racks came ready to install and all it took was a limber nephew to take out the old ones and put in the new. Now I have plenty of spare parts in my own inventory in case the wheels, etc. need replacing.
I feel guilty sending you this repair story because all I did was order the parts on your website and then conned my nephew into making the exchange.
The parts arrived very quickly and in good condition. In fact, the new racks are an improvement over the ones that came with the dishwasher originally. Ms. Susan McNutt was quite helpful in keeping me informed of the status of the part that was back-ordered. It was a pleasure dealing with PartSelect.com.
The wheels that make the lower rack roll had worn out to the point that sometimes dishes would rub against the spray arm.
I removed the old wheel assemblies (4 total holding 2 wheels each) with a slight prying with a screwdriver to ease it off the rack. After the first one, the rest were a little easier. The new ones had to "mate" a certain way and then just needed a push of the hand.
My husband replaced the entire soap dispenser until in under 30 minutes. I stayed out of the room. :) I didn't hear any swearing, so I assume it went fairly well. Sorry that I can't give you detailed instructions. He didn't need a manual or any type of directions. I guess it was kind of obvious how to do it. Just be sure you turn off the power first.
compared it to old rack. Parts snapped together in 5 minutes. the fit was good. Kit did not include the silverware baskets, or the fold down narrow shelf.
removed old check valve from bottom of dishwasher and replaced with new one. I used channel locks to do this, disconnect hoses and screw out check valve, and put back in opposite order, make sure the dishwasher is empty of water or have a plastic bowl or such to catch water. Take off two front covers on bottom of dishwasher to access check valve ,white with hose attached.