Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Replace lower dishwasher rack due to broken tines
Although the lower rack was a slightly different style than our original, it fit the dishwasher perfectly. We needed to transfer the silverware racks to the new rack and insert one set of removable tines. About 5 minutes and we are very happy with the repair.
If your chopper assembly has a catastrophic failure like mine did, chances are it took out the teeth on the circulation motor as well. This will lead to the teeth on the chopper being destroyed by the impeller as soon as you turn the dishwasher back on. First, follow the instructional video to remove the motor (found on this site on the circulation motor page) and chopper assembly (also found on this site on the chopper assembly page). The impeller is screwed onto the input shaft of the motor, and you must keep it from turning so that you can unscrew the impeller assembly. I removed the back cover of the motor (there are four screws holding it on) and held a flat pry bar on the rotating assembly inside the motor to keep it from turning, then unscrewed the impeller from the shaft. Mine came off very easy, but be careful not to let your pry bar slip or damage the motors internals. After that, install the washer and grommet from the impeller seal kit on to the impeller, and screw it back on while keeping the motor from turning with your pry bar. Lastly, reinstall the motor and chopper assembly per the aforementioned instructional videos. The whole thing took around an hour to do, and it is much cheaper than replacing the entire circulation motor.
Dishwasher wouldn't drain; pump drain impeller had come off drive shaft.
Replaced the pump drain as one complete assembly. Couldn't do it from under the front panel as there is a small lug that you have to depress on the top of the assembly before you can twist the assembly counter-clockwise by hand. I tried but I couln't get the leverage. Had to take dishwasher out from under the unit and tip it on its side. The rest was very straightforward. If you can remove the dishwasher from under the unit easily I would suggest you don't even bother trying to change the pump drain while the dishwasher is in place. It's not worth the hassle.
You need to pull the unit out to get access to the spring connected to the rear leg frame. Use the everything in the kit. The rollers are upgraded and will guid the cable better.
First I shut off the breaker for the dishwasher. I had to remove the 6 screws that hold the top part of the dishwasher door to find the panel with the fuse. Then following the instructions that came with the new fuse I cut the wires from the old fuse to remove it. Next I installed the new fuse and attached the wires and then replaced the screws. Turned the breaker back on and everything worked great.
Removed drain hose to ensure no blockage in drain. No blockage, then removed drain pump cap (where drain hose attaches to drain pump) with allen wrench. Push tab in on drain pump and twist counterclockwise, drain pump came off. Reversed to attach new pump and it works.
pull out the dishwasher lay it on its side use a 1/4" drive socket with extension and a universal joint to undo the the hidden bolt, twist the motor 1/4 turn. this is the hard part you have to pull fairly hard and rock the motor around a little to get the o-ring to let the motor slide out. lube up the new motor with jet dry or soap and insert back it, turn it back 1/4 turn, install the bolt and plug the motor control wires back in, then reinstall it back under the counter
If your not getting clean dishes this is an easy check to make that will likely turn out to be your problem. If not, you need to get this far anyway and it's an easy check to make. Remove the top and bottom rack. The bottom and top sprayer are connected together as an assembly by the water transfer pipe the goes up the back side of the dishwasher interior. This needs to be removed. There are two clips that hold the assembly in place at the middle rear of the washer and the top of the washer. Grasp the water assembly with your hand at the location of the clips, top one first and give a twist that rotates the piece out of the clip. Once the assembly is free from both clips hold the assembly at the lower rear where it starts up the back of the washer and move the whole thing to your right to turn the base clockwise. The whole thing will release from the bottom of the washer and come out as one big piece. Set it aside and you will see four torx head screws that were hidden under it. Remove these screws and the round screen assembly that they are holding to the bottom of the washer. Set that part aside as well. Now your looking at the well area where water collects to get into the pump. There will be a little standing water there, it's normal and not a problem. To the left side of the well an inch or two under water you will see one Torx head screw. It's one bit size smaller than the other screws. Remove it and pull up on the cover that it is holding in place. Now you are looking at the chopper assembly, it's a four bladed knife that rotates across the face of a screen. If you can rotate the knife blades and not have the shaft behind the screen move, it bad! Grasp it by the top of the screen and lift it slightly and pull it toward you to remove it. The shaft that turns the blades has worn away where it connects to the blades. It doesn't turn anymore so the screen is plugging and no water is able to get to your dishes. Order a new one and put it back in the same order you took it apart. It helps to have a little screw driver to lift the knife blade away from the screen when your putting in your new part. Load up the washer and give it a test run. YOU DID IT!!!
I removed the dishwasher from under the counter. This took the bulk of the repair time along with disconnecting the water supply and electrical connection. I had enough slack in drain hoses that I could turn the dishwasher over to replace the motor. I was surprised that there was only one bolt that held the motor in place. I put the motor on, turned the dishwasher upright and slide it back unde the counter and began the long process ofreconnecting everything. I am sureit could have gone faster if I were younger and did not need glasses for close work. Start to finish took me four hours. This was the fourth time I have replaced motors in dishwashers of various makes.
Nutdriver, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
7 of 7 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No power to the front panel
Checked the house circuit breaker, verified AC to the box under the dishwasher, removed the screws around the inside door cover, and removed the cover. Removed the outer circuit board cover. Used a multi-meter to verify AC to the door latch, and to verify the latch switch was working. Verified AC to the thermal fuse above the circuit board when the door latch was closed. Verified no AC on the other side of the thermal fuse. Removed the thermal fuse connections with pliers. Used thin flat blade screw driver to unsnap the thermal fuse assembly. Used multi-meter to verify no continuity through the fuse. Ordered the fuse assembly and replaced. Reconnected the thermal fuse connections. Manually closed door switch and saw lights on the display panel, and dishwasher started. Replaced all covers and works great.