Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Replace Soap Dispenser and Door Balance Kit
Need torx to remove front panel. There are four screws that hold the control panel that don't need to be removed. If you do remove them, it helps to put the control panel back before you reinstall the front. The six screws that hold the soap dispenser are a very small hex (<1/4, maybe 3/16). It would help to have some small sockets or nut drivers handy for this.
Lost stop from one side of top rack. Rack could be pulled off track.
Looked at other side of top rack which still had the stop. Just had to orient the direction of the stop and push it firmly onto the rack arm. Took a couple tries, but it went in and locked. Works perfectly. Inexpensive and easy fix to to very annoying problem.
My dishwasher's heated dry cycle wasn't heating up
After pulling the dishwasher out from under the cabinet, I found it underneath near the back right side. I disconnected the old thermostat, unscrewed the clamp holding it into place, put the new thermostat in, screwed it back in and replaced the two plugs. Then I pushed the dishwasher back into place, and it initially didn't work until I found an online forum that was able to identify the reset command for my dishwasher (for the WDT710PAYM4, press any three buttons in a sequence of 1 2 3 1 2 3 1 2 3. After completing that all the lights lit up, and I shut the door leaving it for half an hour) Once the reset finished, the heated dry worked like it was suppose to.
A Mouse friend had seen fit to chew through the original drain line. I used my Model Number, and was able to order the correct part . It arrived the next day. The job itself is fairly straight forward. You will need to access the rear of the machine. This may include shutting off, and disconnecting the water supply line. (Adjustable wrench). Mine is under the sink, on the "Hot" side. You may also need to un-plug the unit. (recommended) . A pair of (Pliers) will be needed for the spring clamp.
The repair would have been really easy if the parts replaced had come all in one...When you order a replacement handle they do not include the 2 small springs.... the springs are a bit hard to get on, but once they were in place everything went well. You need 2 people to assemble it. One to hold the door and the guts of the electronics, and the other to install the handle.
The part snaps on using two plastic retainers (included). You have to pull down gently on the feed tube at the top of the dishwasher to set the top retainer. After that it's a piece of cake.
Unplug dishwasher and slide it out from under cabinet. Remove old broken link (a heavy string between two plastic parts) and replace with new one. Slide dishwasher back and plug it in. Very easy and no tools required.
The old seal would often travel with the door when opened.
I removed the old seal and carefully cleaned the track into which the seal was fixed. No tools other than some ordinary cleaning liquid, cloth and small wooden piece to swab out the track. Easy and quick. As a note here, I first used the incorrect schematic for the unit and ordered the wrong seal. However after receiving the wrong part, I made the correction and reordered. I did this over the phone as I needed instructions to return the part. The person taking my order and answering my questions was very helpful and I want to take this opportunity to thank her.
front seal on the old pump failed causing the front bearing to get wet repeatedly and fail
Removed required hardware and dishwasher from undercounter mount. Turned dishwasher on its front and removed the old motor. Installed the new motor and tested for function. Installed once test was successful.
Noisy rattle in dishwasher since new when it was filling
Remove and replace solinoid, remove and replace mico switch. These are the only two electrically controlled devieces controling water flow. Replacing switch without replacing housing takes a soft touch. A small screw driver helps. Electrical connections have a stay in place nipple. Plyers help get thoes off.
Parts delivered as promised, correct fit. Phone contact available at order question.
Just removed the old seal and followed the instructions that came with the new one. Since the old one didn't have any adhesive on it ,I didn't use the adhesice on the new one. Problem solved!
