| |
19 of 20 people found this instruction helpful
Parts Used
-
- 3rd Level Wash Spinner Kit
Level of DifficultyEasy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerPeter from princeton junction NJ
Old spinner fell after washing the dishes.
Carefully unscrewed the top screw holding the spray arm so it doesn't fall into the tub.
Pull down the arm gently and pop out any remaining parts from the old spinner.
While the spray arm is pulled down, snap the two parts of the spinner together: one from above the spray arm, and one from below the spray arm. (you need to snap them together before you screw the spray arm back, because it won't snap together otherwise.)
Rescrew the spray arm and you are done.
|
6 of 6 people found this instruction helpful
Parts Used
-
- 3rd Level Wash Spinner Kit
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerAl from Yuma AZ
The overhead water spinner became detached and fell off
First I removed the screw from the top water tube and then the upper screw from the vertical water tube at the back of the dishwasher. That gave enough flex to the tube assembly for access to the area I needed to get to, without having to remove it. Then I removed the old spinner retainer and installed the new one. I then snapped the spinner to the new retainer pin, put the tube back into position, and re-installed the screws -- and I was done.
|
4 of 6 people found this instruction helpful
Parts Used
-
- 3rd Level Wash Spinner Kit
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerRichard from Sandyston NJ
Clip no longer held spinner in place
Bent the plastic housing down holding the spinner. Slipped the top of clip in slot on top of housing. Attached spinner and bottom of clip by holding top clip and pushing bottom of clip in place. No tools were needed.
|
5 of 9 people found this instruction helpful
Parts Used
-
- 3rd Level Wash Spinner Kit
Level of DifficultyEasy
Time to do repair:Less than 15 mins
Tools
CustomerBrandon from Antioch CA
Third level spinner fell off
The part snaps on using two plastic retainers (included). You have to pull down gently on the feed tube at the top of the dishwasher to set the top retainer. After that it's a piece of cake.
|
4 of 6 people found this instruction helpful
Parts Used
-
- 3rd Level Wash Spinner Kit
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerRichard K from Bloomington IN
Spinner button broke
Loosened 1 screw to access spinner button. Removed broken spinner button, replaced it with new button,snapped spinner and wedge on button ,replaced screw and was done in about 2 minutes. Thanks for the pictures of installation and the quick shipping of parts. Not to mention the money saved by doing it without a repairman. Thank you
|
1 of 1 people found this instruction helpful
Parts Used
-
- 3rd Level Wash Spinner Kit
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerThomas from Canyon Country CA
Upper wash spinner fell off
It honestly took more time to take the dishwasher baskets out than the actual repair. Once the baskets were out, I put a piece of newspaper over the lower drain in case I dropped a part or the screw. I removed the top screw to access the broken part, removed it, and installed the new spinner. I put the screw back in and 2 minutes later, the dishwasher was in use once again.
Too easy!
|
1 of 1 people found this instruction helpful
Parts Used
-
- 3rd Level Wash Spinner Kit
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsPliers, Screw drivers
CustomerDavid from Auburn CA
Spinner plug missing
gently pulled down the plastic housing for the spinner, pulled the old spinner and other end of plug out, replace all 3 parts (sandwiched the spinner with the male female parts)
done!
about 45 seconds total - no kidding!
thanks much for the great website and comments/feedback
and by the way.... i ordered the part in the afternoon online, next day in the mail i received the part. unbelievably fast service.
thanks again!
//dave
|
1 of 1 people found this instruction helpful
Parts Used
-
- 3rd Level Wash Spinner Kit
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerPatricia from Phoenix AZ
Spinner broke off
took less than a minute to snap it in place.
|
1 of 2 people found this instruction helpful
Parts Used
-
- 3rd Level Wash Spinner Kit
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerNicholas from Ramsey MN
Spinner fell off in dishwasher
There is a plastic part in the dishwasher that looks like a hurricane symbol. It's called a Spinner and it disperses water during the wash and rinse cycles. It is located on the top of the inside of the dishwasher. Unfortunately there is a small plastic part that holds the Spinner in place. This plastic part wears out after a few years and requires replacement. I have replaced it twice - part number 8519736. Very easy to replace - unscrew one screw and put in the part (three separate component) - obvious how it works. Good luck.
|
1 of 2 people found this instruction helpful
Parts Used
-
- 3rd Level Wash Spinner Kit
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerAlan from Waterford CT
Top water spinner fell off
Using past posts, this easy fix only required to bend down the plastic water ducting at the top of the dishwasher, and snap in the upper button to the lower button, which holds the spinner. I put newspaper down on the bootm of the dishwasher, in case I dropped the small plastic pieces.
|
1 of 3 people found this instruction helpful
Parts Used
-
- 3rd Level Wash Spinner Kit
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerBryce from Melbourne FL
#rd level spinner fell off after breaking.
I pulled down on the upper spray arm and took out the broken plastic part and put in the new one then snaped in the retainer part and that is about it. Took less than a minute and did not need to remove dish rack or loosen any screws.
|
1 of 3 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerLee from Prineville OR
Upper spinner broke, also pivot for bottom rack broke in half.
I hooked the pivot on the rack, poof!! Done. I put the spinner pieces together, (they don't need any tools) then I just snapped them in the upper "hole" where they belong and voila!! Done.
|
1 of 3 people found this instruction helpful
Parts Used
-
- 3rd Level Wash Spinner Kit
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsNutdriver, Screw drivers
CustomerMichael from Billings MT
Had to replace the top spinner
Took 2 screws out of intake tube and replaced spinner. It was very easy.
|
1 of 4 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerDon from Phoenix AZ
Spinner broke, had to be replaced
There is a button that connects the spinner. It wore out, and the spinner fell into the top rack after a use of a cycle one day. Your diagram of the dishwasher was very helpful to understand what part to order. Your delivery was swift, and we only had to hand wash dishes for three days. Thank you for your excellent web page design and service. I will use your company again!
|
0 of 1 people found this instruction helpful
Parts Used
-
- 3rd Level Wash Spinner Kit
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerDean from Austin TX
The 3rd level wash spinner had broken
Easy as pie. If you can build with Legos you can do this. It takes about 60 seconds! Really. Just follow the instructions given by others (although I did not remove the upper screw, I just carefully pulled the upper arm down about 1"). Insert the keeper button in the top, insert the spinner in the bottom and snap together!
|