KUDH23HY1 KitchenAid Dishwasher - Instructions

Used screwdriver to pry off other end of water tube. Kind of cooked on over the years and rear connection point is on a part that is not real strong so you have to be careful to not break or bend the connection. New tube is very tight to get on so putting it on required using the blade of the screwdriver to get the tube to streatch over the two connection points, but not real difficult. Now it's good as new!

First removed old hose from the upper rack. Used hair dryer to heat the hose up ( hose was a little stiff) and installed hose. It's pretty simple to install, I didn't even have to unload the dishwasher

The whole operation took about 5 minutes which included opening the package! Sprayed some vegetable spray inside the opening of the water tube that attached to the spray connection and it slipped right on. Absolutely amazing and I feel like I have a brand new dishwater! My dishes are definitely cleaner too! Thank you Parts Select for posting how to instructions!

It was easy to remove rack from dishwasher. I screwed on rollers and it was like new!

Part was easy to locate on the website. Photo on the measurement grid was the key after entering the maker and model number. I have found refrigerator parts the same way on this site. Sliced the old rotten hose to remove it. The new hose only had to be slipped over the connections. I soaped the ends of the tube to make the installation easier.

I just slipped the old, worn out tube off, warmed the new one in some hot water for a few minutes to make it more pliable, sprayed some non-stick spray on the end connecting in the back, and slipped it on. Piece of cake!

I pulled off the broken parts and snapped on the new axles, then replaced the wheels. Very simple.

i pulled the rack out, took off the old parts then added the new ones. it was quick and simple. i needed no tools and my package of parts arrived quicker than i thought. thanks!

I removed the old tube by hand (it fell apart) I just worrked the new softer tube over the openings on each end and it was fixed! I did have to warm the new tube with warm water to squeeze it over the tubes but it was easy!

Actually I ordered the drain and wash impeller kit because it was listed as the #1 cause of failure to drain. I then hired a plumber to install it. He did so and that didn't solve the problem. So I was about to buy a new dishwasher. I then noticed that the second most frequent cause was a problem with the "dishwasher drain check valve." I watched the "partselect" video on how to change that. I didn't have a new one but I thought I would take out the part and see what I could learn. As it turned out it was blocked by a little piece of what appeared to be a walnut chip. I cleaned it out reinstalled the drain check valve and the problem was solved.

Used a utility knife to cut the old tube . It was hard & brittle & full of holes. The new tube is not very flexible. Ran it under hot water to soften it up. I used liquid soap on the ends . This made the repair easy. Slipped right on, at both ends. Saved $200 by doing it myself. Took ten minutes.With more pressure from the new tube, the dishwasher is cleaning much better.

Manually remove old tube and simply replace with new tube - no tools!

I removed the old, brittle and leaky water delivery tube by hand and at the outlet and at the inlet end, by cutting it away with an exacto knife. I then heated the new tube under hot water and coated each end with dishwasher soap. With only a modest amount of manipulation, both ends slipped easily into place and the hose was immediately secure and operable. My wife, who didn't witness my efforts, thought I was a genius.

I took out the bottom rack, turned it upside down, popped off the wheels and saved them and put on the new axles. It took a little doing to get the new axles snapped into place-they were stiff. I finally figured out how to use the pliers at the right angle to pop them on. Then the wheels popped right on and off I went.

removed screws from dishwasher and discovered i could replace panel because of door type