KUDF230B0 KitchenAid Dishwasher - Instructions

First removed old hose from the upper rack. Used hair dryer to heat the hose up ( hose was a little stiff) and installed hose. It's pretty simple to install, I didn't even have to unload the dishwasher

I pulled off the broken parts and snapped on the new axles, then replaced the wheels. Very simple.

i pulled the rack out, took off the old parts then added the new ones. it was quick and simple. i needed no tools and my package of parts arrived quicker than i thought. thanks!

I pulled back the tray and inserted the funnel like part into the rubber tube. That was it. I wonder where the original part disappeared to.

I removed the old tube by hand (it fell apart) I just worrked the new softer tube over the openings on each end and it was fixed! I did have to warm the new tube with warm water to squeeze it over the tubes but it was easy!

Part was easy to locate on the website. Photo on the measurement grid was the key after entering the maker and model number. I have found refrigerator parts the same way on this site. Sliced the old rotten hose to remove it. The new hose only had to be slipped over the connections. I soaped the ends of the tube to make the installation easier.

I just slipped the old, worn out tube off, warmed the new one in some hot water for a few minutes to make it more pliable, sprayed some non-stick spray on the end connecting in the back, and slipped it on. Piece of cake!

I ordered 8 new axles and used old wheels. I broke off the remaining axle parts left on the wire lower basket with just my hands, and then popped on the new axles. This was done without tools; just needed significant pressure to pop the axles onto the coated wire. The wheels popped onto the axles with a little pressure. Make sure you have the right side of the wheel out. I simply looked at the remaining working wheels before install began to make sure which side goes out. Very easy install.

It was easy to remove rack from dishwasher. I screwed on rollers and it was like new!

Actually I ordered the drain and wash impeller kit because it was listed as the #1 cause of failure to drain. I then hired a plumber to install it. He did so and that didn't solve the problem. So I was about to buy a new dishwasher. I then noticed that the second most frequent cause was a problem with the "dishwasher drain check valve." I watched the "partselect" video on how to change that. I didn't have a new one but I thought I would take out the part and see what I could learn. As it turned out it was blocked by a little piece of what appeared to be a walnut chip. I cleaned it out reinstalled the drain check valve and the problem was solved.

I removed the old, brittle and leaky water delivery tube by hand and at the outlet and at the inlet end, by cutting it away with an exacto knife. I then heated the new tube under hot water and coated each end with dishwasher soap. With only a modest amount of manipulation, both ends slipped easily into place and the hose was immediately secure and operable. My wife, who didn't witness my efforts, thought I was a genius.

Used a utility knife to cut the old tube . It was hard & brittle & full of holes. The new tube is not very flexible. Ran it under hot water to soften it up. I used liquid soap on the ends . This made the repair easy. Slipped right on, at both ends. Saved $200 by doing it myself. Took ten minutes.With more pressure from the new tube, the dishwasher is cleaning much better.

Manually remove old tube and simply replace with new tube - no tools!

The water inlet valve SEEMED to be the logical choice of the part that went bad. It was! It was a really easy fix. Undo the bottom front of the dishwasher. Shut off the hot water supply. Unscrew the hot water pipe leading to the valve. Unscrew the 2 screws holding the vlave to the dishwasher. Unclamp the rubber hose on the other side of the valve leading TO the inside of the dishwasher (water outlet side of the valve) And remove the electrical plug on the old valve. Only time consuming part was the need to remove the male/female coppper fitting from the old valve, put it on the new one and reattach the hotwater pipe....don't forget the teflon tape on the threads, the elecrtrical plug, the rubber hose and the front of the case . My wife says it runs like new

FIrst I shut the water and power off. I took 4 screws off bottom panels of dishwasher. Using pliers I move spring clip of the rubber valve. I disangage the hose and disconnected electrical connection ( two wires ) . Then using two open wrenches ( 3/4" and the other probably 13/16" - not sure ) disconnected the copper tubbing. I replaced the valve i reverse order.I used teflon tape for sealing connections . Everything works good now.