KSRP25FNSS00 KitchenAid Refrigerator - Instructions

Completely disconnected the power. Just shutting off the ice maker switch does not shut off the power to these boards. The emitter and Receiver boards are located in the side panels of the freezer-one on the right and the other on the left. Just remove the 3 screws in each cover and disconnect the wire connectors and install the new boards. It's very straight forward and easy to do.

I replaced the thermometer first and it started working again. I was convinced that the reason that it continued to break every 6mos was because no one had ever replaced the fan. The difficult part was getting to it. After trying to get in from the front and from the back I finally figured out that I had to take the bottom off and tilt it on its side. I was then able to get out the pin in the condenser and move it to the side. I could then reach the screws that held in the fan. I then decided to put the fan on the motor and when I was tapping it on with a hammer the back cracked. I attempted to fix it by taking apart the old motor and salvaging the parts but that didn't work. I had to buy another $85 part and take the whole thing apart again. It was easier the second time because I knew which screws and pins I had to remove and how to get to them. I very, very carefully tapped the fan onto the motor and now it is working fine. I will let you know if it is still working at Easter. If it is I will have done a better job than the 7or 8 repairmen who have fixed it in the past

from the back of the freezer unscrewed the water feed to the feed tube. unscrewed the tube from the freezer and removed it. Ran hot water through the fill tube and then reinstalled the tube back into the freezer. Cycled the ice maker and the water started filling the icemaker. Did not use the water inlet valve that I ordered. Matter of fact.. I returned it. Always remember to check the fill tube and make sure it is not frozen.

I followed the video instructions to replace the ice maker controller. Works like new. Each to order from website, part arrived in 3 days. I'll certainly order from partselect.com again.

Your repair video was spot on. Should have watched it before I removed the old defective part. Would recommend it for anyone with same problem. I'll call on you again. Thank you. Billy

I removed the old water inlet valve and replaced it with a new one. I had to cut the existing water lines with a razor to fit the new design of the new inlet valve. I also had to remove the inlet water valve and attach it to the new one. It was real easy once I reviewed the U tube video on how to replace the valve.

Remove the door on the icemaker. Remove a screw on the bottom right of the icemaker and remove the bracket. push two small tabs on the bottom to release icemaker and slide out. unclip plugs that are on the wire. To reinstall just do the reverse.

Got the main bolts off and unplugged and removed the ice maker. Had to remove all parts and rebuild it on the new mold. Was more complex than I thought but was able to get it done. Note where everything was as you take it off and you'll do fine.

Turned off ice maker and removed the old filter at the lower front grate of the refrigerator. Replaced it with the new filter. Turned knob and was done!

I removed the top door hinge cover, removed the top hinge, pulled the refrigerator door off, layed it on the floor, removed the door cams, installed the new door cams, replaced the doo and top hinge and hinge cover. If you have this problem with your refrigerator door, be sure to replace the upper and lower cam.

Followed instructions- removed and replaced with new water inlet valve also replaced control bracket. Now no leaks and plenty of ice thanks to partselect, the right part, the right price and fast delivery . Thank you

Repair was so simple, I didn't even need instructions. Removed old fan with motor, installed new one, installed harness that converted plugs, done. Saved hundreds of dollars doing the repair myself.

I unscrewed the (3) screws on the bottom of the ice maker & the (1) screw on the electrical cover plate. I unplugged the ice maker & completely removed it from the freezer. Make sure to pay attention to the locking tabs or your maker will not come out. I took the bottom plate off the old ice maker & attached it to the new one, slid it in & re-plugged it. Tighten all screws back where they are to go & now I have ice. It was a breeze to do this job. Part was completely as described.

removed front trim, removed plastic bracket, removed broken ice guide, installed new ice guide, installed removed items in reverse order, finished.

removed the 3 screws from the receiver first, on hinge side with the flap The toughest part was twisting my arm around and upside down to plug the new board into the wire harness since it had very little slack and the wires were stiff from cold, the emitter on the opposite side was as easy, care needed to be taken with the upper screw partially hidden behind ice maker itself but it was an easy removal. Again, short wires and stiff from cold make alignment of the plug to the board just bit awkward to ensure it was seated properly. 15 mins later I heard the first emptying of the ice maker