KSRP25FNSS00 KitchenAid Refrigerator - Instructions

Video instructions walked me right thru it had no problems.

turn power off, take the little cover on front of ice maker off so you can pull ice maker box out easier, unplug the easy connector ,after this take square cover off you'll see control motor take 3 screws off pull control motor out change new one in ,put them back together.turn power back on .then now Ice Maker will make some after 2 hours .You will SMILING then say ,Oh Yeah. QT good luck to everyone

The online video shortened the learning curve, and the cut the repair time in half.

Removed and replaced retaining clip and installed a new strain relief. Parts arrived in 2 days from the time they were ordered. No problems whats-so-ever. Great doing business with Parts Select again.

I bought the part from Part Select and they sent a video on how to install part.

Put part on /did not see warter come at first had to go a cycal then ice again thanks alot, danny repair guy whanted 46$ to look at part. Good job.

My ice maker has been broken since august 2011. I called my son in law, which is very handy, he looked at the broken ice maker, said he had no clue how to fix it, since its computerized. Searched the internet, found part select website, watched videos, read customers feed back, based on information provided, ordered icemaker control and motor assembly (less than $60. 00), Called my son in law, in less than 10 minutes, part was installed. The next morning the ice bin was full. I am so greatful for your website, and my wonderful son in law.

The video on the website on replacing the Icemaker Assembly is great. I watched it then performed the R&R. It would have taken less than 15 mins but I took the time to clean the components which were reused. The water receiver on the new assembly is taller than the original. Luckily the water outlet in the freezer is rubber so I was able to bend it out of the way so I could slide in the new unit. The wiring plug in the new assembly was installed in reverse of the old one so I had to pull the unit back out, turn the wiring plug upside down, put it back in place then re-install the unit. Had a couple minor changes to make but the video is a great teacher.

removed the ice container, remove the two screws that hold in the shaft and seal. use pliers to remove worn out shaft, drop in the new shaft and seal reinstall the cover with the two screws and your done. took maybe 5 minutes start to finish.

Unplugged the refrigerator then removed two vertical screws on the very back back of the control panel (the ones with the washers). Do not remove the four other vertical screws in the panel. The front plastic plate on control panel snaps off and there are two horizontal screws under the plate. Remove them and the control panel will drop down allowing access to the light switch. Unplug the two wires (one black and one white) from the old switch. Discard the old switch, snap the new one into place and reconnect the two wires. Snap the front plastic plate back into place, plug in the refrigerator and you are done! Problem solved with a new $16.00 switch and saved at least $75.00 or more from an appliance repair call. Thanks Part Select!

Read the reviews on how to test if part was bad. It was! Ordered new infered sensors and watched your repair video! 2 hours later the ice maker was making ice:) Very easy! Thanks David

Removed icemaker and installed the new one. Went from six tiny ice cubes to four big ice cubes. Ice is of a higher quality, and the ice no longer falls out of the bin as the old ice maker's ice had once been prone to doing. A certified epic win on my part.

Install was done in reverse order of uninstall. The only thing that made this install a bit tricky is that the fill cup on the replacement icemaker was not the same part as on the original. I could have attempted to trim the replacement fill cup but didn't know how well that would work. I instead elected to install the original fill cup onto the new icemaker. This added a bit of time and complexity to the repair but I followed a repair video for when just the ice mold is being replaced. That video told me how to disassemble the ice mold and timer motor which had to be done to in order to replace the fill cup. It's been about 2 weeks since repair was made and the icemaker seems to be working properly.

TURN OFF WATER (if not already). Cut (or disconnect filler tube at bottom). Remove faceplate from refrigerator ice/water dispenser area. Remove screw holding metal bracket that holds water tube at filler point. Held metal mounting bracelet and pulled old filler tube out. Fed new filler tube thru bottom (hole is located at bottom of left door at hinge). As tube came out at top, pulled length needed to mount to new mounting bracket. Remounted new bracket (with hose attached) with new screw. Reconnected tube at bottom water line connection. Turn on water.

I could not pull the water filtering housing far enough forward to disconnect the water tubing lines (short tubing line). I had to remove the cover from the back of the refrigerator, disconnect the tubing from the back and then pull the water housing forward to disconnect the tubing from the housing. This added another 20 minutes to the job. Otherwise the installation went well.