KSRJ25FXMS03 KitchenAid Refrigerator - Instructions

Removing the panels inside the freezer section was the most difficult ,because it is narrow,hard to fit your body inside compartment, in order to cut wires and to splice Bi-metal Defrost Thermostat wires (2 ) Watch the videos on the web site so you know where to start. First time I ever "repaired " a large appliance, saved me over $ 600.00 (that's what the people I bought the Refrigerator from wanted to charge me.) My parts cost 65.00 !!!!! My younger brother turned me onto the web site... , I'll be returning to the site and telling my friends about it. It's a total "rip off" what service organizations charge the general public these days from Car Dealer ships to the stores we purchase our appliances from. !!! Glad I still have my health and faculties to repair the essentials we have around our homes. !!!!

took cover off, installed bulb.
lost the owners manual,
part select's schematics were very helpful
thanks

We took out the old filter and put in the new one. Ran out a few gallons of water then it was ready to use.

plastic warped in ,spaced out and, the socket snapped back in place.

I unplugged the refrigerator
Opened the freezer door
Opened the ice maker door so that I could easily get to the emitter and receiver
I used a phillips head screw driver to remove 3 screws from the emitter plate and 3 screws from the receiver plate
I unplugged the faulty circuit boards--this took some tugging
I firmly plugged in the new circuit boards and replaced the screws
I waited about 30 minutes and the ice maker began making ice again

Ordered the parts from Parts Select and had them within two days (lightning fast shipment--and with just standard shipping). Disconnected the power to refrigerator, removed three screws from each cover panel, pulled the panels loose from the freezer wall, disconnected the wiring harness on each, removed the screws holding the two boards, replaced the boards with the new ones, attached boards to cover panel with screw, reconnected wiring harnesses, replaced the three screws on each side, restored power, and made ice! Whole job took about 15 minutes.

After receiving the replacement emitter and receiver boards from PartSelect.com, I following the troubleshooting paperwork that came with my order to ensure the parts I ordered where the problem. After which, it was very straight forward: unplug the frig, unscrew the 3 screws on the covers for each board, unplug the push-pin connection, remove the board screw, set the new board in, and plug back into the connection. It took approximately 20min.

Unscrew the three phillips screws holding the flipper and electric eye unit, pull it out a bit to unplug the connector. Take the assembly over to a flat surface, and use pliers and or crew driver to pry/pull off the press-on retainer on the hinge pin. Pull out hinge pin, remove the broken flipper. Put new flipper in place making sure spring is behind the flipper (holding it open). Reinsert hinge pin, and then reuse the press-on retainer to hold in in place. Then take the repaired assembly back to the freezer, re-plug the plug, and then reinstall the unit using the 3 phillips screws. Easy Peasy.

Light was blinking on the Electronic Control Boards. Ordered replacement (emitter and receiver)and installed, and now it's working.
Some note: 1 year ago, the board started to blinks (meaning it's bad) but it was still making ice. This gave me a false error when it really failed, took the risk and ordered the replacement parts and all is well now.

One more thing to pay attention to , and it may only be on my model of refrigerator, but the wires harness that connect to the receiver board (big board) have large and stiff wire. With limited space where the board and the wire are seat at, it put lots of pressure on the pressure on the board's connector. This pressure, over time, will cause the right angle connector's solders to crack and may be a contributor to the failure. If you're installing the new board, try to re-inforce the connector with some rubber heat glue and also relieve pressure from the connector's end, which I hope will prolong your board.

Repairing a refrigerator is inimidating to say the least. Our ice maker has broke twice in the two years that we have owned it. The first time we had a service repair faciliting come out and they replaced it for about $200. The second time I had no idea what the problem was until I came to this repair forum. I soon realized that the electronic control boards needed to be replaced. Received the part two days after ordering and it took all of about 5 minutes to unscrew the old boards, pop them out, and put in the new ones.

Love your website and the money that you saved me!!! Thanks a million!

i did the repair exactly like the instruction VEDIO!

I followed your instructions , the only thing that was left out was that the freezer has a drain hole that had to be thawed out with a hair dryer,till the water went to the drain pan underneath the ref. your instruction were through enough, that's why I purchased the part from your company, I installed the part 2 days ago and its working like new again 23.00 for the part instead of 1200.00 dollars for another ref. thanks very much. 6 months ago I purchased the relay and compressor starter from your company at that time per your instructions I shook the compressor starter and like a light bulb it had something broke inside,I needed that thanks again oomk

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

power off, 3 phillips head screws on either side of freezer. unplg each board, plug new ones in completely. ( cannot mix them up, size difference) replace screws and enjoy ice cold beverages once again!!!!!!!!!

Contacted sears home service to perform repair. Quote for repair was $307. 43. ( $196. 90 For labor ,$102. 58 For part) plus $75. 00 For service call. Based on the charge, I refused the repair and ordered the appropriate part from "part select" (733947) (wpl 8201515) motor module for a cost of $81. 84. To my surprise, the part arrived the next day and in 15 minutes the icemaker was in a position to make ice, and has been producing ice ever since. To perform the module replacement, I had to remove one screw with a nutdriver, pull the icemaker out, disconnect a wire harness, replace the module and do the reverse procedure to complete the installation. I saved a total of $225. 59 By doing this repair myself. A lesson learned. . . . . I will always investigate doing a repair myself with the help from the people at part select. Very professional and they sent the correct part the first time.