KSRA25FKSS00 KitchenAid Refrigerator - Instructions

Replaced the optic boards - no lights working. Still no ice. No water coming into ice machine. Followed instructions on your website and diagnosed frozen line. Took ice machine out, used hair dryer, reinstalled and we have ice! Thank you so much for saving us a repair bill!!!!! Buying the part from you was very easy and your videos were excellent!!!

Get help from part select

Removed two hex head screws, installed new part with nut driver for two hex head screws , very easy. I broke the tab off the hinge for the ice maker door when I installed a new ice maker the week before.

Replaced the Crisper Drawer Cover and Shelf Frame with the new one - less than 4 minutes. Thanks for sending me the exact part.

Used flat blade screwdriver to remove old guide by spreading the remaining top tabs. Inserted new guide and tipped the top forward to line up bottom tab in slot. Used screwdriver to push in tab. Once it was seated pressing in the top snapped the guide into place easily.

The video on replacing this part was spot on. The screw was a little difficult to remove at first. It had been installed ten years earlier and also had some thread lock installed. A light swat with a hammer on the end of screw driver as I was trying to remove it got the screw started without stripping the Phillips head. Once we got by that little snag, it's a piece of cake, or piece of ice if you prefer.

Got Online to Parts Select put in the model number, selected from parts schematic, Ordered parts. Reviewed YouTube instructions supplied by Parts Select, Canadian service tech in video very knowledgeable about repair, followed his instruction and fixed the Ice maker. Very easy with Parts Select help.

I Googled the problem and after reading several posting & suggestions decided that the Ice dispenser kit would probably solve the problem. I ordered both parts on the chance that it might be only the micro switch and it was only a $10 part, the ice dispenser kit was $50. The access was really easy and the switch was installed in about 20 minutes but did not solve the problem so I proceeded with the kit. The parts came out fairly easy but our actual set up was slightly different from the video and print instructions. Our model did not have the heating ribbon on the door flap and the little barrel part was permanently attached to the refrigerator so I thought I could be in trouble. Did not realize that we had cracker the lever bracket clip during removal so my husband "brainstormed" a fix. That's what we needed the large head screw and drill for. We drilled the screw into the refrigerator so it holding the spring loaded piece tightly in position. Works fine. I was told my a repairman over the phone that the dispenser was probably not fixable on our model. I saved an expensive service call AND GOT THE DISPENSER WORKING!

Followed recommendations from others but went with most likely by percentage = defrost timer kit. Did not solve issue. Then went with bi-metal thermostat and that did not fix the problem. Tested the thermostat as recommended on line and old part was bad, new part ok. Then I saw on line that I should have listened for fan operation. I checked and found the fan motor to be defective. Replaced the motor and refrigerator worked fine. Both the motor and bi-metal thermostat were required. Should have checked fan operation first.

I followed along with the Video from the web site. I used the masking tape to keep the electric parts out of the way. one of the attaching points for the new ice door broke off so i used J B Weld to reattach it. then the repair was finished with out a hitch. The time was extended by the need to wait for the epoxy to cure

Followed the instructions on package, went extremely well, with no problems what so ever! Thanks so much for the part and how to do list!

The drawer just had to be replaced.

It was fairly easy my 4 year old daughter helped me, I replaced the electronic boards with ease, the light worked but the water was not coming to the ice maker I checked the line noticed that there was Ice buildup inline so I used a tool to crush the ice and used the the turkey baster to flush the line with hot water, after that the ice maker started to work I saved a lot of money.

The ice dispensor guid went in very quickly - just as the video indicated. The rear, side stays were a little tight, but it now works great. The plastic bracket holder for the water and ice switches had broken holders for the ice switch. The video was very clear, and disconnecting the electric above the door made the job easier. My arrangement is a little different from the video (no screws holding the outside cover no the inside bracket box). But, the repair went quickly and I would have had a lot of extra problems without the video as a clear and detailed guide. My only wish was to have seen the videos before purchasing the parts. I highly recommend your parts, quick delivery, reasonable prices, and excellent video repair guides. Thanks,

My handyman did the repair. It was pretty easy for him. It would have been a real puzzle if we had not watched the video instructions. The new parts were slightly different than the old parts, but they fit perfectly. I thawed the frost buildup around the ice door and the opening of the ice bin with a hair drier, to get the ice to come out properly. Thank you so much for the video!