Models > KSC24C8EYY00 > Instructions

KSC24C8EYY00 KitchenAid Refrigerator - Instructions

All installation instructions for KSC24C8EYY00 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KSC24C8EYY00
61-66 of 66
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

NEEDED MORE SHELVES & BINS

  • Customer: KENT from GRAND JUNCTION CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
ADDED THE SHELF & BIN

Freezer OK. Refrigerator Not Cooling.

  • Customer: Donald from Kissimmee FL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed recommendations from others but went with most likely by percentage = Defrost Timer Kit. Did not solve issue. Then went with Bi-Metal Thermostat and that did not fix the problem. Tested the thermostat as recommended on line and old part was bad, new part OK. Then I saw on line that I should have listened for Fan operation. I checked and found the fan Motor to be defective. Replaced the motor and Refrigerator worked fine. Both the Motor and Bi-Metal Thermostat were required. Should have checked fan operation first.

Ice maker would not disperse cubes through the door

  • Customer: Danny from Fulton MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Looked at drawing to see what sequence the parts went.

refrigerator and freezer would stay frozen.

  • Customer: Jack from Poplarville MS
  • Difficulty: Really easy
  • Time to Complete: More than 2 hours
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I shut the unit off for about ten hours and when I turned it back on and set the temperatures for the freezer and refrigerator it has been working great.I will keep the part in case it happens again.

water line leak. wet cover

  • Customer: james from altadena CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
replaced plastic water line with stainless steel water line, then removed wet cover, cleaned water in bottom of refrigerator, then dried it with a portable heater. When dry, installed new cover.

This was a side-by-side unit. The symptom was: ice in bottom of freezer; vent tube to evaporator tray blocked by ice; dispenser ice melting together; ice cream much too cold; and defrost and freezing cycle too long.

  • Customer: Robert from Weymouth MA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
All food and drawers were removed from the freezer, including ice tray. The left side shelf brackets were removed to ease removal of the back panels which expose the the bi-metal defrost thermostat. Six screws to remove the large back panel, plus the shelf support rails needed to be loosened to remove the smaller upper panel.
The bi-metal thermostat is mechanically clipped to the upmost coil of the condenser. the two wires must be cut and wires for the new thermostat spliced in. The wires were tinned with solder to insure a good connection, then twisted and crimped with an automotive end connector. With the smaller 22.8 cu.ft. refrigerator a lot of the work will have to be performed with one hand. The hardest problem here is diagnosing the malfunction correctly in the beginning. I was impressed that the replacement part was received in two days ...
All Instructions for the KSC24C8EYY00
61-66 of 66