KGST307HBS4 KitchenAid Range - Instructions

Watched video and followed the very accurate and helpful instructions. A #2 Phillips screwdriver was the only tool required. This is an easy job for the average person.

There are already good instructions here on doing the repair, so I will just add what I found important. 1) using penetrating oil and an impact wrench on the screws that hold the inner glass to the inside of the oven door - they were rusted tight. 2) the outside glass front sits on the front of the door, on top of the edges of the side pieces, even though it looked to me like the side pieces were meant to go over the edges of the glass - they aren't. The bare side edges of the glass aren't covered with any trim at all. The video on removing the oven door that matched the kind of hinges I had showed taking them off the door as part of disassembly of the door. I didn't find that necessary at all, and you probably won't either. Less parts to have to get back in place. The hard part to me was finding the correct disassembly video to match the oddball hinges, which isn't to say it's a bad design - actually it seems better that the other more common designs. Take out the two screws above where the hinges enter the range, and lift the door up, away from the range, and off. Easy peasy.

Video's did not show my door construction so I had some difficulty and surprises. One must disassemble and keep all parts in order of disaasembly with all screws for each part.separated. Be methodical and patient and it will all work out.

Remove old knobs and replace with new ones!

Replaced damaged drawer roller: easy peasy!

The old part, including lightbulb and socket, had corroded into place, and the glass light cover was stuck to the socket. I used a dead blow hammer and a dowel just under the diameter of the hole to tap on the back side of the socket to loosen it and get it out. The metal tabs on the old socket were folded back to make it fit better (?), which made it harder to remove. Lots of muscling of the part to get it out. Easy to install new part once old one was out of the way. An experienced person would have removed the old part and installed the new in no time.

removed door from range and slowly took apart until reached inner glass. there are three pcs of glass, front and two inner. was able to clean the inside which was dirty after 15 years of use. took alittle over an hour from start to finish including thorough cleaning.

Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.

Pop old one out and new one in

It didn't. The grate pads (PN# PS389174) were too small for the grate (W10311216) and wouldn't work. (PN# recommended by Whirlpool parts department) The pads were smaller in diameter and shorter. Yes I could have glued them in, but because of the size the pads would be flat in no time. The only thing I could order from KitchenAid was the total grate. I ordered the pads late December, they were backordered. I got them the 1st week of February. I tried getting through to Whirlpool by calling to see if there was something I could reorder, but no luck, couldn't through. Am I unhappy? Oh some, but I handle it. Its not the first time I have been rode hard and put away wet.

My son had first removed the 2 screws to disconnect the damaged element. He then removed the element
by pulling it out and disconnected the wires.

I was si grateful when he was able to connect the new igniter so we could have cookies for Christmas...thank you for your very prompt delivery of the element and the ease to reconnect it.

Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.

replaced light socket but did not repair problem. must have burned the motherboard.


pleased with service from your company.

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.