Models > KGSC308LSS0 > Instructions

KGSC308LSS0 KitchenAid Range - Instructions

All installation instructions for KGSC308LSS0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KGSC308LSS0
46-60 of 105
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

OVEN LIGHT WOULD NOT WORK, OLD BULB BROKEN

  • Customer: LOUIS from FREEPORT TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 5 people found this instruction helpful
HAD ALREADY REMOVED BACK COVERS AND DISCONNTEDTED POWER. WHEN IO RECEIVED PARTS I REPLACED THEM IN REVERSE ODER I HAD REMOVED THEM. TOOK ME LONGER TO REPLACE BACK COVERS BECAUSE OF MY BAD DIABETIC HANDS. THANKS VERY MUCH, YOPU SAVBED ME A BUNCH. GOD BLESS YOU AND YOURS, GOD BLESS AMERICA.

replaced two baffles

  • Customer: Glenn from Bonham TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 2 people found this instruction helpful
took off the dryer by remving two screws, then the front panel. Then removed the screws that held in the drum, pulled the drum out replaced the baffles then put it back together. It was easyer then I thought. It took less them 30 mins.

Replace Gas Cooktop bad surface Igniter

  • Customer: Charles from Williamsburg VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
1. Turn off Gas at valve under cooktop. Unplug electric to igniters. 2. Remove all control knobs. 3. Remove grates and burner covers. 4. Remove screws from each burner head (10 screws) 5. lift and remove cooktop cover. 6. Reach under cabinet and push up main cooktop body (about 4 or 5 inches) and BLOCK. 7. AT FRONT OF COOKTOP REMOVE 2 philips screws holding burner strip. Slightly lift burner strip enough to get short handle philips under screw holding igniter (Be gentle as gas line is still connect and will give enough so as not to have to disconnect them. 8. Remove and replace igniter. 9. Reverse procedures above.

Both left and right door hinges broke off their pins

  • Customer: Tracy from Thousand Oaks CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
The first time I took the door apart to see what part to order it was difficult. The second time I knew what I was in for and was more prepared. Replacing the hinges were no problem. It was taking apart the door that was more difficult.

electrical short from oven light.

  • Customer: William H. from morehead city NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 1 of 3 people found this instruction helpful
I trouble shot and traced out to electrical short in face panel and found burnt wires. I've been a licensed electrician for years and it takes alot of comon sense to trouble shoot and find problem. I found schetch-matic of appliance and searched computor and found partselect.com and tried it. It wasnt no time and the part was at my door. Thank you partselect and i would use them again in the future. billy

broken inside oven door glass

  • Customer: Louis from Puyallup WA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
The repair went very well the most difficult was getting the door off. There is a certain way to do it as the springs in the door are very strong. It went well except for a small cut a thumb. The repair is easier with two people at least to get the door removed. You must be very careful to remember how the door comes apart. Be careful to not touch the glass putting it in once it is installed it is impossible to get the finger prints off. With help of a friend or in this case my son along with a couple of bloody marys it went well and we had fun.

thanks

2- Burners would not spark to light

  • Customer: Lyle from annandale NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
Received the New Spark Harness with in 2 days after ordering from Parts - Select !!! And had intstalled in 15 minutes

Block broke

  • Customer: Edward from Crimora VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 1 of 3 people found this instruction helpful
Unplug power cord, remove wires from block. take 2 screws out. replace with new block about 15 mins. Done

Both outside door handles turned very beige

  • Customer: Howard from Boynton Beach FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 4 of 12 people found this instruction helpful
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

broken inside door glass

  • Customer: welborn from hutto TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
took the door off, removed the screws, removed the back of the door, took the broken glass out, put new glass in, reassemble door, put door back on.

Cracked inner door glass pannel

  • Customer: Pat from Queen Creek AZ
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Removed door parts & cleaned each, till the glass was reached. Replaced glass and reinstalled parts in order removed.

Broken inner oven door glass

  • Customer: Terrence from Bloomingdale IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
This worked very well, thanks to the advice posted from other users. The only part that was a bit unclear was removing the door. There are small, slotted metal pieces screwed into the sides of the oven to hold the door hinges in the slots. After removing those, I had to hold the door and push it up and down, and a little bit side to side, to get the hinges to start sliding out, but they did. There are no other screws or brackets holding them in place. The hinges are on springs, so they do snap up when they come out of the slots in the sides of the oven. But they only snap to a 90 degree angle, so they won't cut your fingers off. You'd have to hold your fingers right on them to even get pinched. After that, I just kept taking screws out of the door until I got through to the back panel, replaced it, and put it all back together.

broken inside glass

  • Customer: mike from orland park IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
After reading what other people did for this job I figured I could do this. The inside glass broke after liquid accidently hit the glass from basting.
Just followed the digram from the internet to show how the door and glass comes apart. The only thing I had to figure out was how to take the door off. And once I figured that out it went pretty easy.
The door comes off just by lifting up on the door and pulling out. Just make sure you put all your parts in order on how they come apart and just replace them them in that order.

broken glass

  • Customer: Rowenna from yukon OK
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 2 people found this instruction helpful
I refered to what I had read on repair stories of broken glass...then went to fixing mine and before I new it I was done and glass replaced...it was very easy as long as you watch what you are doing when u take it apart and replace things the same as they were removed......thank you

burned oven bulb

  • Customer: Ivanka from Atlantra GA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 2 people found this instruction helpful
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.
All Instructions for the KGSC308LSS0
46-60 of 105