Models > KFCS22EVMS1 > Instructions

KFCS22EVMS1 KitchenAid Refrigerator - Instructions

All Instructions for the KFCS22EVMS1
61 - 75 of 615
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Refrigerator wouldn't cool
First I removed the six screws from the cover. I then disconnected the two wires and pulled the small motor out with its base and removed two screws that hold it in place. I then changed the old one for the new one and set it back in its place. I then set the cover back and turned it on. I was happy again.
Parts Used:
Freezer Evaporator Fan Motor - 115V 60Hz
  • Fidel from Forest, MS
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
10 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
no water when under sink water filter installed
I called the installer of my filter unit and he told me that often, thhe fridge filter is the problem. Like magic it worked
Parts Used:
Refrigerator Water Filter Bypass
  • Emi from Arlington, VA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
11 of 19 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Would Not Make Ice.
After lots of internet exploring and diagnosis, the icemaker comes right out, and with three screws out and in, the job is all but done. Don't pay anyone for this repair!!!!!
Parts Used:
Icemaker Motor Kit
  • Zach from Danville, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
8 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Mold Ice Heating Element Broken
Looking at the ice maker it is pretty cut & dried as to how to remove the unit. I took out the ice tray and just started removing all the mounting screws. The same for the mold ice tray & heating element. I was just sad that you did not have just the heating element separate from the mold ice tray.
Parts Used:
Ice Mold
  • timothy from indio, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers, Socket set
7 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice maker leaked into ice reservoir
The ice mold has a coating on it. Over time the coating deteriorates. If your ice maker leaks water into the ice reservoir inspect the mold to see if the coating is compromised. If so, replace with new.

Remove the ice maker assembly. 3 small hex screws. Unplug power cord. Disassemble ice maker assembly. Remove ice mold/heater. Replace with new. Reassemble.
Parts Used:
Ice Mold
  • joe from hilliard, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
7 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The plastic pin on the end cap holding the lid to the "Deli Center" drawer broke when the refrigerator door closed with the drawer open.
1) Remove Deli Center drawer and lid 2) Remove the two Crisper Drawers above the Deli Center 3) Remove the glass shelf above the Crisper Drawers. 4) Remove the front and brackets that held the glass shelf. 5) Remove the broken end cap by sliding it upward off the brackets that hold it to the side of the refrigerator, 6) Slide on new end cap. Replace the other parts in reverse order of removal. You will probably want to clean the parts you have removed before reinstalling. Easy- peasy.
Parts Used:
Pantry Drawer End Cap - Left Side
  • Jim from PLANO, TX
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
8 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
replace freezer door gasket
first pressed in two bottom corners then used fingers to press in bottom section,pressed in two top corners then pressed in both sides using fingers followed by pressing in top section using fingers.VERY EASY !
Parts Used:
Freezer Door Gasket - Apollo Gray
  • Russell from ROCK HILL, SC
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
7 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking water tube connector/union
Received the union I ordered, then discovered that the tubes were different sizes, so I had the wrong part. I had read elsewhere that it was necessary to trim the two ends of the tubes with a box cutter to stop the leaks - I did this, and the leaking stopped. I was then able to go to a local hardware store and get a 5/16 to 1/4 union and replace it. The leaking is stopped, and the water supply in the door is now working like new. No problem with partselect, but I did buy a caliper so that I can check tube diameters if I ever have a similar problem! This is a great site to find instructions - well worth the time to search!
Parts Used:
Water Tube Connector/Union - 5/16 to 5/16
  • Roderick from NEWTOWN, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
7 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door bushing
I bought a set of appliances used online and the fridge door did not align to the other door. I quickly noticed I had lost the lower bushing to the right door upon transportation so I did what any man would do...find a way to fix it! after checking out a few websites I ran accross Partselect and after seeing their "dummy proof" diagrams It was certain I couldn't mess this up considering the loads of bushings to choose from. The order was placed Monday morning and to my surprise I had a package the VERY NEXT DAY!! AMAZING delivery time and quality products. PartSelect is definately my appliace parts source from now on! Thank you!
Parts Used:
Door Closure
  • Carlos from Streamwood, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
8 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Black flecks in ice
The lining of the ice mold (Whirlpool) started flecking off (black flecks in the ice cubes), so I decided to replace the mold.
Loosen the two 1/4 inch upper nuts and remove the lower nut to remove the ice maker from the freezer. The hardest part was getting it unplugged. I used a small blade screwdriver to release the catch on the connector and pull it out.
Remove the ice maker front cover. If you have a skinny enough phillips screw driver, there are two deep set screws through two holes on the lower portion of the control module (otherwise, remove the three screws on the controller, unlatch the shut-off arm from the control module, and separate the controller to access the mold screws). Unhook the shut-off wire from the end of the tray. Unscrew the two screws holding the mold and remove the mold.
Remove the plastic hardware from the old mold and install on the new mold.
Attach the new mold on to the control module.
WARNING WARNING WARNING!!! The mold I bought already had the alumilastic on it for the contact point to the thermostat. When I installed it and tightened the screws, the alumilastic was dried out, didn't squash down, and dented the bi-metal thermostat on the controller, ruining it. I had to buy a new thermostat. Be sure to check that the alumilastic is pliable. If not, take it off and buy some fresh to put on there.
Re-install the ice maker. It took a while to get the first batch of ice because the ice maker was at room temperature and I had the freezer door open for several minutes. So the freezer had to get cold and the ice maker had to chill down. Once everything got cold, it started making ice again.
Parts Used:
Ice Mold
  • Anthony from Billings, MT
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Screw drivers
6 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The Freezer defrosted and everything on the top and the bottom spoiled
i had used your web site before and i read several problems that your readers had. i went to the back of the unit, removed the bottom cover and right there the i found the run capacitor and i chaged it. since i had only ordered this part to save money i went back and ordered the Start Device which when i took it off it was completely burned. the replacement part came labeled with 2 different compressor #, so i picked the one that i had and unpluged each wire. the part may differ from the one that it's in the unit but it worked when i pluged everything back on. it also helps to take a picture of everything before removing the wires in case you have to leave it and come back later. i hope to use this refrigerator another 10 years. thank you all for your help.
Parts Used:
Capacitor
  • Jorge from Miami, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
9 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The "axle" for the Deli Center lid broke when struck by an orange dropping from above.
You need to remove both humidifier drawers plus the glass shelf for the bottom of the humidifier drawers and the bar at the front as a start. If I had known this before starting it would have sped up the install time. Then, pull out the deli drawer.

To remove the end cap (either side) there is a plastic tab to push down on just over halfway back and then you can slide up the front of the end cap. Once you have slid up the front of the end cap a few inches, (past the channel it is locked into), you can pull it forward. You can observe the configuration on the spare part to see how this needs to be done.

To install the new end cap, reverse this process. The trickiest part is then re-inserting the deli drawer and the lid. Getting the lid onto the two axles was a bit of a struggle as the fit is very tight. Re-installing the humidifier parts is much easier. My repair time included using the opportunity to clean all of the removed drawers and shelves. If you know about the need to remove the humidifier drawers ahead of time and eliminate the cleaning I think this would take less than 15 minutes.
Parts Used:
Pantry Drawer End Cap - Left Side
  • Bruce from KIRKLAND, WA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
6 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken latch on water filter cover.
Reviewed replacement instructions video on your website. Just followed the easy instructions to pop out old cover and pop in new cover. I would not have tried to replace it myself had I not seen your video. Super easy.
Parts Used:
Water Filter Cover
  • Gloria from Laurinburg, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
6 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Pin holding darwer lid boke off.
Must remove all shelves, pantry drawer , bins above pantry drawer.
Once everything is out of the way grasp the old, broken end end and pull directly straight up, if the refrigerator is a little older it may take a very strong pull. Needless to say this model is the newer model with no screws holding the end cap in place.
Once the old piece is out just located the three pins position the new piece over these pins and press down should clip right into place.
Very easy after old piece is removed.
Take a picture of the bins and drawers before you start so you have a reference when returning those pieces back.
Parts Used:
Pantry Drawer End Cap - Left Side
  • Jack from HOLLAND, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
6 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
ice maker not operating
Unlug refrig or turn off refrig from its control panel On/OFF switch.
For ease of work remove freezer shelve directly below the ice maker. Remove four screws from the bottom of the ice maker assembly, three that secure the ice maker and the other that holds a plastice shroud in place over the ice maker's power plug.
The ice maker is now ready to be removed; it will slide forward by pushing up on left and right side of the ice maker's mounting slide rails. Once the ice maker is moved forward it is easier to disconnect its power plug (depress a locking tab on the side of the connector and pull connector apart and remove ice maker assembly.
Remove and replace motor module by removing three screws and and replace with new unit.
Reverse ice maker removal proceure for installation. Once installation is completed turn on Power to Refrig, Ice making should begin after a few hours.
Parts Used:
Ice Mold Icemaker Motor Kit
  • Dennis from Sebastian, FL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers
6 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the KFCS22EVMS1
61 - 75 of 615