KEYW777BWH0 KitchenAid Dryer - Instructions

I lifted the top of the dryer cabinet, like the hood of a car using a screwdriver to pry it open. I removed the two screws in the upper right corner of the cabinet front. I disconnected the safty switch on the front door. The front of the cabinet can then be removed by lifting up the front off the pins in the base. With the drum exposed you can place the belt on and thread it through the two pulleys on the motor. Consult the diagrams provided on the PartsSelect website for the proper positioning of the belt on the pulleys. After the belt is installed spin the drum by hand one turn to make sure that it is seated properly on the drum and pulleys. Reassemble the dryer in the reverve order.

I used a screwdriver to remove the old part and pushed the new part in with my fingers, it was very easy. If I could do it, anyone can. I was a lot cheaper then having a repair man come to house. I am very glad I found your site online, I will definitely be using your company again.

I looked up the procedure to remove the switch in a repair book, removed the broken switch. Then I reconnected the wire leads, put the part in and closed everything up. The part arrived so quickly and there were even instructions with the part which made the repair go so easily.

pressed clip into hole on top of front panel. first remove two philip screws that hold filter so you can lift top up.

Pulled to old out inserted the new. I would like to say your turn around from date part was ordered until I recieved it was three days, I find that amazing. I'm still waiting for a part I ordered from another company 1 month ago. The price was right shipping cost was very reasonable and your web site extremly easy to use. Thanks very much, Al

removed the catch and the pin and replaced it. We were sent a couple different sizes so we tested the one that looked like the closest match. I think the pin was made with different thicknesses of metal. Worked great and saved us from having to get a new dryer!

This was so much easier than I though it was going to be. Pulled up on the top part of the dryer and folded it over to the back. Removed 2 screws for the front panel and disconnected some wires. Laying down I fed the new belt on and made sure the tensioner was put back into the right spot, because when the belt broke the tensioner sprung to the other end of its travel. Put everything back together. This was made super easy because you guys had the parts and the shipping was super fast. Alot of the local shops in the area didnt even carry the belt or were not helpful..

Repair went well, but my switch only had one contact on the non common end. The new switch had two contacts. One is for operation with lid open and one for lid closed. Make sure to connect to the lid closed contact and the common on the other end and leave the lid open contact unused.

Prop up the hood of the dryer with flat bar. Take out 2 screws holding dryer front end and 2 switch screws for dryer light inside dryer door. Secure dryer drum with bungee cord. Lift front end and remove. Remove broken belt. Route new belt over drum and pass underneatch idler pulley at botttom of dryer. Apply pressure to idler pulley w/one hand while securing belt around motor with the other. Make sure drum seals are snug between front and back of dryer while putting everything back together.
Have confidence. This is a very easy fix.

First I unplugged the dryer from 240V and removed the back cover upper (behind the switch) and lower (exposing the remainder of the parts)

Inside the upper section was a folded wiring diagram of the dryer (don't know if this was courtesy of Whirlpool or another individual, but it was a very nice touch.)

I did a resistance measurement across the heating coil and found out it was fine. I then plugged the dryer back in and carefully took voltage measurements from one phase of power (this was easily accessed where the power comes in to the dryer, just be careful not to touch or short the wires)

I had an assistant turn on the dryer (this makes things go a little faster, as you are behind the dryer otherwise) and checked for 240V across the heater coil.

Once I did not have this, I kept one lead on the left side wire (one of the power phases coming into the dryer) and moved the other lead to the left (as viewed on the wiring diagram) until I no longer had 240V. This identified the faulty component as the Thermostat High-Limit, non resetable.

I ordered the kit with the High Limit NR and High limit Thermostat (as both had to be bad). I also ordered the 150 degree cycling thermostat (although this was not necessary - for <$20 I opted to replace it as well)

Removing wires one at a time, each component is fairly easy to replace.

My only complaint is that with the combo kit, the wire attachment is a little different that the original component and requires you to cut an existing wire and crimp a different terminal to allow all three wires on the High Limit thermostat (250 degrees) to be attached. There is little to show you how exactly the crimp is to be connected (it goes on the smaller of the three wires - DO NOT CUT the jumper provided and USE A GOOD CRIMPER - not the $2 variety, or you'll be getting a new connector!!) The connector provided is designed for some strain relief from one connector to the other, however) An additional jumper with the appropriate connectors already attached would be a nicer design.

Also, make sure you do NOT screw in the smaller cover that covers the power in until you place the entire lower half cover back on the dryer (unless you want to take it off a second time, as I did...) as it uses a common screw to hold both in place.

Overall, fairly easy to do with a minimum of tools, straight blade screwdriver to remove stubborn wire connectors (esp. for HT thermostat 250), ratchet and socket for quick removal and replacement of covers, and a good T&B style crimper ($10-$20 at your local hardware and well worth it even if you only use it a couple of times)

30 minutes and done - the dryer now cranks out the heat and the advanced settings (Auto dry) work great - no more 2-3 times throug to get things dry.

If you have a minimum of mechanical ability and a little bit of electronic troubleshooting skill, you can check and repair this youself and save about an $80-$100 service call.

Thanks to Part Select for the diagram of the dryer layout as well!! (Schematic would be nice if available online, though!)

Shipped the part in about 2 days from order time, as well. Will be back (hopefully not soon, though, as something has to break first!!!)

Be safe and good luck!

(One last note: Make sure your lint trap is clear including the hose - either due to build up or a lazy kid...as this probably caused the failure as heat could not escape...)

I first disconnected the power cord and the vent hose. I removed the screws on the top of the back side to raise the top of the unit. There are also 2 screws holding the lint filter shoot which were also removed to allow the top to be lifted up. Its not necessary to remove the top since this would require disconnecting the wiring harness etc.

Next I removed the 2 screws located on the top-inside surface, which connect the front panel to the unit. After these were removed, the front panel lifts up and off--there are two clips which slid free on the bottom of the unit. The shut off switch on the door has to be disconnected to remove the panel.

With the front panel removed, the drum can be removed. I vacuumed out the interior and retrieved the idle pulley which had popped loose when the belt broke.

I removed the old rear drum seal and cleaned the edge with some brake cleaner solvent and steel wool. I then wiped the edge with paper towel and more brake cleaner to remove any oily residues. Before applying the glue, I test fit the seal which turned out to be a bit tight, so I stretched it a bit around the drum until it would fit on easily.

I used a disposible glue brush to spread a thin layer of the contact cement along the edge of the drum. By the time I finished one round, the glue was dry where I had started and so I did a second thin coat.

I then oriented the seal as per the directions and began fitting onto the edge trying to keep the free felt surface from getting into the glue. By the time I had reach the opposite side, the belt was pretty tight and so I had to stretch it a bit to get it to go on. I then worked my way around the edge a final time insuring that the seal was positioned correctly all the way around and the glue was pressed tight. I let the glue set for several hours before reassembling.

After the glue was dry, I put the drum back into the unit and worked the seal up onto the circular back panel until the groove on the drum was correctly positioned on the rear rollers. I propped the front edge of the drum on two 2 in rolls of duck tape so that I could rotate the drum freely several times. I checked the outside and inside to be sure that the seal was not turned under any place.

Finally, I slipped the new belt over the drum and past my 2 rolls of tape and positioned it groove side in over the drum. I then reinserted the tensioning pulling back into the slot just in front of the motor. The pulley goes just to the left of the motor pulley, the end of the tap on the base inserts in a slot and then 2 pins rest in a second slot to the right of the first. A loop of the belt then passes through underneath the pulley and then over the motor pulley. This requires pulling the tensioning pulling pulley towards the motor to get enough slack. I then rotated the drum several times and made sure that the belt was not twisted and the groove side was towards the drum.

To help hold the drum up while I was fitting the front panel. I supported the drum with a piece of 2 in tape run from the top/front edge of the drum to the back panel of the unit. I removed my two rolls of tape from under the unit, slipped the front panel back onto the two bottom clips, and then worked the front open of the drum over the front seal by opening the door and pushing from the inside and rotating the drum. I replugged the door switch and made sure the wire clips were secure.

I then replaced the 2 screws to hold the front panel. I put the top back down and resecured the screws on the back before reattaching the hose and replugging the unit. I test ran the unit for several minutes empty, listening for weird noises that would indicate something didn't go together correctly.

Old door catch came out, new one slipped in. All works great.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Half of my pulley was broken off so there were no wrench flats to take it off. I was able to remove it using Channel Locks and the 7/16 wrench shown in the video.

Hint: Use a one gallon ice cream bucket to hold up the drum while connecting the belt. It makes it much easier and gives you more clearance.

Do to age and heat the dryer door handle was brittle and broke. Ordering was easy on line. Part was delivered faster tan expected. Oh and the repair time, Less than 1-minute.

Thanks for the great service.