KERC600EWH1 KitchenAid Range - Instructions

I screwed the light lens into the socket and went beautifully. Better than the original. (I am a retired, 75 yr. old woman).

removed back of stove, removed 2 screws holding element, disconnected element and removed it, then reversed procedure. excellent service from part select and will use them again when needed.

removed the worn out roller...inserted the new roller....tightened the nut...it was finished...this was without a doubt the most pleasent repair from start to finish..only took 3 days from the time i orderded the part to completing the repair...i would advise anyone to use " partselect.com" without hesitation

In my situation, removing the control panel first required pulling the range unit forward to expose the side screws, which first required removing the screws holding down the stove (tilt prevention. Those screws are accessed by removing the bottom range drawer). Replacing the switch was a breeze. Very important to label wires before removing them from the old switch. Also, over the years, food liquids that spilled on the range top "gunked up" the front gasket seal of the control panel. Suggest cleaning the gasket as part of the repair - something a DIY should always do! Leave it better than you found it. When I removed the current switch, I could tell by looking at the LED terminal post there were burn marks which suggested there was indeed a fault in it. For about $45 I replaced a switch that would have cost over $200 for a repair person to come.

Had already removed back covers and disconntedted power. When io received parts I replaced them in reverse oder I had removed them. Took me longer to replace back covers because of my bad diabetic hands. Thanks very much, yopu savbed me a bunch. God bless you and yours, god bless america.

Moved stove away from wall, cleaned ( hadn't been moved in 17 years). Disconnected Dual Broil Element, replaced with a new one, stove worked fine.

I tried taking the sensor out, but the plastic coupling behind the oven wall had melted and the melted piece was larger than the opening in the oven wall. I had to use a mini-screwdriver to chip away at the melted coupling before it would fit through the opening. That took forever...but it finally worked and the repair went quickly (15 minutes) after that.

I didn't. Don't know how to get to light bulb to change it for this specific model

Removed broken glass cover and bulb, cleaned old gasket off with damp cloth and replaced with new bulb, glass cover and gasket. No tools needed.

Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.

I live in a small town in South East Colorado. We have just a Walmart and Sears and a few smaller hardware stores. I checked all of them to try to find this 25 1/2 inch Fluorescent Light Bulb, and nobody carried one. I would have had to drive 70 miles to find one. The Service of Partselect was wonderful and the bulb showed up in just 4 days. I was lost without this light. I have bought a few other items for my older appliances in the past from Partselect. com and was very happy with the service and how easy the web page is to navigate. .

Repair was very straightforward. Based on information gathered from an earlier post about the same repair I simply removed all screws from the oven door. These were all located on the bottom edge of the door itself. Upon removal of the screws the door separated and exposed the "core" where I then had access to the hinges which were held in by one screw each. I removed the broken hinge, replaced it with the new hinge, pieced the door back together, put back all the screws, and the repair was complete.

finally figured it out , but instruction sheet could have shown old switch terminals & new switch terminal locations.

Unscrewed about 10 screws to disassemble the door to get at the hinge then screw new hinge in. Was inspired by the woman who said she did it while watching a child. I saved $200 in the repair fee I was quoted

REMOVE BACK COVER. UN PLUG, REMOVE TWO SCREWS IN SIDE OVEN, PULL OUT , REPLACE, REATTACH, FIXED CODE F-3