KEDS200YWH0 KitchenAid Range - Instructions

Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.

Started out removing the old clip that didnt hold burner element down anymore. It was a bit rough, since i was taking off a rivet. I used the screwdriver to carefully wedge the edges of the rivet upward so that i could get the wire cutters underneath it enough to snap the head off. After some fanagling for about 20 minutes, i popped it off. The rest of the repair went like cake, and i am soooo thankful that the replacement part i ordered from you included a screw and a nut. Next time, if there is a next time, this repair could be done in 2 minutes. THANK YOU FOR SAVING THANKSGIVING AND A $100 REPAIRMAN SERVICE COST FOR A $10 PART!!!

Simple to do. Remove old element, remove screw holding socket, cut the socket wires with 2 inches to spare, assemble the newsocket and wires with heat shrink tubing, strip range wires, apply the wire nuts as instructed and shrink the tubning with a heat gun.

Screw on the socket to the range. Shut the lid and install the element.

The replacemnet screw is thicker than the original one, so you might want to drill out the hole very slightly. I did not but the resistance was high on getting the screw fully seated.

Works great

First, shut off the power at the breaker panel. Next, I simply unscrewed the screws holding in each element, disconnected the leads, reconnected the leads to the new elements, positioned each element & reinserted the screws. A suggestion: Before loosening the screws, a light shot of PB Blaster or similar might help.

I didn't. Don't know how to get to light bulb to change it for this specific model

Remove burners using my hands and replace new burners using my hands.

Plugged in the new burner, which we received in one day.We were delighted with the quick service

simply turned off power. took old element out, held in by two screws. pulled out far enough to take off wires. removed and replaced with new element. that was a purfect fit. Works great.

1. Turn off circuit breaker, pull out element and remove reflector pan.
2. Unfasten terminal block mounting screw and remove terminal block from casing.
3. Cut wires as close to defective terminal block as possible (not as per instructions) since you will need the maximum possible length of wire.
4. Slip on heat shrink sleeves, strip stove wires and connect to new terminal block per instructions.
5. Heat shrink sleeves per instructions.

Removed 2 screws holding element in place. Pulled out element to access two wires. Slid off the old element connectors. Placed new element in place and attached the two wires. Pushed it back into place and replaced the screws. Done in 10 min max.

Removed 3 screws on bottom edge of door,2 screws on top edge of door. Outside of door comes off. Then use a 1/4 nut driver and remove glass window supports until you get to the inner door glass. Reverse to assemble. Gasket was okey.

Take the time to pull off the door from the hinge; which is to simply pull it up to release with the door open approx. 4 inches. Have a Philips head screwdriver and a nut driver set available. Keep the screws grouped and the take it apart in the logical sequence. It took about 30 minutes total to complete the job. But then again, it was a woman who did it!

took out the old heating elments and cleaned the bottom & top of oven with out the elments in, which made it alot easier then put new ones in. They were very easy to do, just make sure you watch how you took old ones out and don't loose the screws cause you use them to put new ones in.

removed old Plug-in block by removing 1 screw and cutting 2 wires. (Screw was so tight and rusty that I had to use vise grips to remove it). Installed new Plug-in block with wire nuts and heat shrink wraps. YOU just have to make sure the wires are seated in the block properly. This job was much easier than I anticipated. The burner works great now!

First I removed the bottom oven drawer from the stove. Then I removed all the screws from the outer oven door. Then I removed the screws from the inter door panel and needed assistance to remove the first glass panel and frame. Then I removed the second panel of glass and frame. Then I removed the third panel of glass that was broken. The gasket was the last part to be removed. Getting the new gasket to stay put while putting the new glass panel next to it was the hard part. I needed assistance to place the glass against the gasket and then place the frame back on this panel. Once this mission was accomplished. It was a matter of getting the next glass panel put back in the frame. and replacing the inter door panel and putting the screws back in. Then I put the third glass panel and screws back in. Once this was accomplished , I put the outer door back and put the screens back in the outer door.