KBFS25EWBL7 KitchenAid Refrigerator - Instructions

took out broken part put on new part was easy

It was very easy I just push ito n and it snaped right in.

Took out the old part(2 screws) and installed the new one and it was fixed, very easy and rewarding, for $20 this was great, a service repair company wanted $150 just to assess the problem.

The nipple on the "pantry end cap - left side" that acted as part of the hinge for the meat drawer cover broke off. After receiving the replacement pantry end cap, I removed the meat drawer, removed the 2 vegetable bins, removed the glass shelf above the meat drawer, removed the screws holding the old pantry end cap, and pulled the old cap out. Then I put the new cap in place, screwed it in, and replaced everything else. The most surprising part of all of this is that I ordered my part on 4/22 and received and installed it on 4/25; 3 days! Thank you partselect for your fast response.

Found glass here and ordered. Had it 2 days later and set new glass in and back in business.

The rail & the drawers need to be aligned with each other & then push the rail into the little hole in the back wall of the frig while sliding the drawers in at the same time. I think I put too much fruit & vegs in the drawers which makes them heavy & the little tab which is there to support the drawers has broken off twice. This is the 2nd time I have ordered this rail. It would be helpful if the rail had a vertical supporting post towards the front. I like to have a lot of produce on hand all the time

Removed Left side support with broken pin (3 small hex head bolts). Replaced with new support with pin in place. Note behind: I broke the pin trying to replace the cover. Now I know to flex back the side to the cover, and not flex the pin which broke. This cost me 25 bucks and one hour, saving me from a probable $300 dollar charge. THANKS, PARTS SELECT!!!!!

Removed long drawer. Unscrewed the end cap. Removed slider from broken end cap. Reconnected the slider to the new end cap. Screwed new end cap in place. Replaced drawer. Done!

Remove all three drawers. Remove the glass panel. Remove screws from pantry end cap. Remove end cap from refrigerator. Remove temperature control assembly from old end cap. Install temperature control on new end cap. Install new end cap in refridgerator. install screws. Put glass panel back in refrigerator. Put drawers back in refrigerator. Install drawer lid on new end cap. Close the refrigerator. The part arrived within two days. The repair took a total of 20 minutes from opening the box with the new part to closing the refrigerator door after the job was complete.

Removed the six screws holding the bottom access plate found at the rear of the refrigerator. This gives you easy access to the run capacitor that has a retaining clip. Remove the wire clip and pull out the capacitor (it has two quick disconnect terminals). Reverse the process using the new run capacitor to complete the repair.

Took shelves and crisper drawers out, took broken left panel out with nut driver and then replaced with new part. Installed drawers and glass shelf and finished.

This is an easy fix, simply remove and replace. What I was impressed with is that a how to video was provided along with my part. I wish all manufactures would offer this, the video was easy to understand and you had a good view of the operation. Thanks, a job well done.

This rail holds up the two crisper drawers.It was easy to select and order it on your website. It arrived in a few days with standard shipping instruction, and snapped in place in a few seconds.

I watched the on line you tube video on how to DIY. The putty knife worked to pop out the switch. I used the standar screwdriver to unplug the switch from the wire harness. Then plug in the new switch and pop it back in to the roof of the freezer. Tip: watch out when ordering the new switch - the freezer switch is different than the refrigerator switch. The freezer has three prongs. The fridge has two. I initially ordered the wrong part and added a week to the repair time and had to pay shipping to return the first switch.