KBFS25ETSS01 KitchenAid Refrigerator - Instructions

turned off the water supply,disconnected the power from icemaker to the back wall,loosened the two screws on the top,and one screw on the bottom.removed old icemaker.took the bale off,to put on the new icemaker.removed the wire harness from the old,to put on the new icemaker..saved over $200 for the repairman,had a full tray of ice in 6 hours.(watching the video,helped)!!!!!,very thankful for your service,as most of my appliances are all in that ten year period,i will be ordering more as needed.

So easy! IDed the part with ease with the pictures.When the new part arrived, removed 2 screws from the old part and 2 nuts.Then removed old part and replaced with new part, which fit perfectly.Replaced screws and nuts, put the drawer and lid back on and done! I am a not very handy 58 year old female and this was easy.

Removed the 2 veggie drawer, removed the meat /pantry drawer and shelf. unscrewed the screws, removed the end cap and replaced it with new end cap - screwed the screws back in and voila - DONE!

Removed the 2 bins, glass shelf, large drawer. Removed the 2 screws holding the right drawer slide. Removed the 2 screws holding the pantry end cap in place. Transfered all the parts from the old end cap to the new end cap and reinstalled the end cap. Replaced the slide, glass shelf and the drawers. Installed the large drawer cover (very carefully!) as this is what broke off last time. Total time start to finish about 30 minutes.

Empty out freezer loosen two top screws and took out bottom screw. Lifted out ice maker and unplugged wire. Took bailing arm and plug and put on new ice maker and reverse the process. Had ice in three hours and no leaks.

The repair was simple. It was a matter of unpluging the old relay and then pluging in the new one. I almost bought a new refrigerator but after doing alittle reading on this web sight and finding out the most common reason for having the problem I was having I decided to order the relay. It was the problem...$ 70.00 -v- $1400.00. I'm HAPPY !

Was very easy after I found right tool to get out the screws. There were only 3 popped old one out and put new one in. I waited over a year thinking this was a difficult/expensive repair. So not true...22$ and 15 min. I will definitely recommend this store/site and maintain it for my future use.

Removed wiring from old ice maker and install on new. With 2 screws all ready in place hung ice maker on them. Attach wire connector into socket and install bottom screw to hold ice maker. Tighten top 2 screw and put wire guide in place. Drop wire guide down and ice started in 10 mins

had to replace side cap s because plastic pin sheared off

I first reviewed the video, paying attend to the order in which items were removed and put back in place. On the video, I noticed that the lid to the draw was put back into place before the draw. Following these instructions, the repair went extremely easy and fast. I would recommend reviewing the video first.

The pivot block looked slightly worn because the hinge door mechanism on the left door would not "close" when the door was opened. I bought the pivot block, but the fix is adjusting the dual french doors so they are even i n height at the top of the unit. Pivot block is a 2 minute job with screwdriver. Adjusting the height is a 5 minute job with nut driver.

The icemaker in my Maytag refrigerator was having a few problems. First, a small leak developed in the ice cube tray, allowing water to drip into the ice bucket. This of course caused the ice to become one solid mass, totally inappropriate for a gin and tonic. After a couple of months of this, it stopped working altogether. On to the internet I went, and discovered how easy this repair actually was. One nut to remove, one to put it back in. The installation video was very helpful. I did have a concern at first because the icemaker did not start making ice rights away. I thought it might be a defective unit. It took about 12 hours to get the first batch and it has been happily cranking out the ice since! Ed in upstate New York.

All you need to do for this repair is to remove one nut with a nutdriver. The part is removed by lifting upward. The wire assembly is disconnected. The new rail is installed by using the reverse order. That's it. Changing the pivot block is a no-brainer.

Simply remove the two fruit/vegie drawer and the glass pantry top. Lift off the front support for the glass. Using a nut driver, remove the 2 screws that hold the pantry cap onto the side of the fridge then remove the end cap and temperature control. Remove the two screws that hold the drawer slide to the end cap and transfer to the new end cap. Now transfer the temperature control slides from the old end cap to the new. Some twisting and bending of the plastic slides will be necessary so be carefull not to push too far and break them. Reverse the removal until everything's back together.

disconnected el. power to fridge. pried out broken switch with small screwdriner and pulled out w/water pump pliers. installed new switch and pressed into opening.