KBFS25ETSS01 KitchenAid Refrigerator - Instructions

The part came in 5 days from time order. take less then 10 minute done. part work well, have ices again, Thank you Part Select. we don't have to buy a new Rerigerator

Removed pantry slide out drawer, removed both upper drawers, removed glass shelf (below 2 drawers). Removed the front glass shelf support. It just sits in a grove, comes right off.Used a ratcheting screw driver,with no tip, to remove the screws holding the end cap. Disconnected the air flow adjusting lever from end cap.Cleaned the whole area with a sponge and soap and water.lol.( amazing how dirty it can get being out of sight). reinstalled the lever on the new end cap, screwed it in place, put everything back together, DONE!It took about 20 min, including cleaning.Oh yeah, had an "inservice" with my grandaughter on how to close the 'fridge door.

I started by changing the water inlet valve. It made one batch but it did not eject into the ben. I removed the ice maker and found that the coating inside was bad. I changed out the ice maker and it is now making lots of ice.

I turned the water supply off and installed the new filter, which was easy. the hard part was finding the water filter at my local home improvement stores; they don't carry it. In the future I will use only Part Select.

Looked at the appliance's booklet to see how it fit together, then installed it.

PartsSelect makes it so easy. I love that they inlcude a picture of each part so I am sure I am buying the right thing!

I went on line and viewed the video. It looked so easy I ordered the new ice maker. Having the information I was able to take apart the old one and view the problem. By the time the new part arrived I was experienced with the installation. I was shocked when the new ice maker arrived within 1 day. I completed the installation without a hitch, I was delighted with the ease of installation and the operation of the new iace maker.Thanks again...Ray

This was sooo easy! Removed the vegetable bins and shelf. Then removed the the deli drawer and lid. Used a 1/4 inch nut driver to remove the three nuts. On kitchen counter, I removed the two cross-cut screws from slide rail and put it on the new piece. Replaced the three nuts on the new end cap and then the hard work began---clean the shelves and bins that had been removed and replace the food. My refrigerator looks like new!

went by instructions, used a little common sence.

I removed contents of freezer as this was a bottom unit. I had to remove freezer drawers/door to easily access ice maker which was located in the back of unit,wasnt a problem.I did however take a hair dryer to water tube as it froze up with about an 6 inch tube of ice that finally slid down. Connected unit and had ice within an hour or so and a full tray within 24 hrs. Second ice maker in little over a year...Video very helpful, saved 100 bucks by doing myself. Part arrived fast, great job!

Removed drawers, screws and cap and replaced. Very easy and excellent service in shipping.

We ordered a PartSelect PS2121513 ice maker. I was concerned that there was no instructions shipped with the unit. Fortunately, PartSelect had an online video that guided me through the process. It wasn't that complex really. The only time I felt totally dumb was when using my nut driver to remove the bottom bracket. I couldn't figure out why there was no 1/4" socket with my set, so I used a small socket wrench instead. I finally figured out that the driver was already a 1/4", without a socket in it. After that it was easy. Slid the ice maker up a little to free it from the top mounting screws. Pulled it outward a bit to gain access to the connector at the back of the freezer, then squeezed the two sides of the connector and out it came. I popped the plastic cover off the existing device and then removed the connector as instructed in the video. I also removed the bale (as per the video). I put the connector harness, plastic cover and bale on the new ice maker and put it back in, this time using the nut driver on the bottom bracket :-). My only concern after that was that it didn't seem to be working. I had no idea that it needed some time to get cold before it would work. After about an hour, it filled with water and began making ice. Success.

All I needed was to replace a can holder in the door of my refrig ( since I don't drink pop/soda it was wasting space ) with a more useful bin to hold items like condiments/salad dressings. Popped one out, the new one in. . . . simple. I do appreciate the fact that this site made it easy to get the right item , and the item arrived the day after I ordered it. Thank you so much.

Pretty easy to do except need to pay close attention to how the old part came off because the back was a little tricky. The part that hooks to the chefs pantry door and controls the temperature adjustment slide pay particular attention to. The whole job from start to finish about 30 minutes, definately would not hire someone to do, would do myself again.

Removed shelves to allow access for removal of end cap. Remove three 1/4" drive screws and pull end cap forward to loosen and remove. The back assembly for temperature control of the bins will come out too. Remove temperature control rod and back assembly from end cap for reuse on new end cap. Remove two philips screws from drawer slider and detach from end cap. Reverse process for re-installation.