KBFA25ERSS00 KitchenAid Refrigerator - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broken pantry end cap
The repair was straight-forward once the pantry drawer and lower shelves were emptied and removed - remove the mounting screws, replace the broken end cap with the new part. It took me several minutes to reattach everything. It took me longer to clean up all the old food spills under the pantry drawer.
Parts Used:
-
Carter from Athens, GA
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Repace Water filter
-
Nancy from Urbandale, IA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Ice maker stopped working. Turned out a connection on the heating bar shorted out.
Pulled the plug on the refrig. ( This is important since the heating bar on the bottom of the ice maker could come on as soon as you plug it in and burn your hand ). Removed the ice bin to get it out of the way and then removed the 1/4" hex screw from the support bracket under the old ice maker ( don't lose it ). Pushed up on the old ice maker to dislodge it from the 2 support clips on the top of the ice maker. Squeezed both sides of the wire harness plug and pulled it out and removed the old ice maker. Removed the wire harness and level bar from the old ice maker and installed them on the new ice maker. Plugged the ice maker wire harness into the female receptacle in the freezer. Popped the ice maker in to the top support clips making sure the rubber water chute from the refrig. was in place in the round ice maker receptacle. Plugged bak in the refrig. and I was getting ice in about 2 hours. Working fine after 1 week producing plenty of ice. RussK---
Parts Used:
-
Russ from Supply, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
ice maker stopped making ice
following the advice of this site, purchased a new ice maker. Old one was simple to unhook and remove and new one was just as easy to install. Within no time at all, I had ice being made and it has been working perfect since. Thank you for the help...
Parts Used:
-
David from Jacksonville, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Broken prong that held the lid for the drawer
Removed the old bar. Replaced the part that moved the shutter open and closed. Installed the new parts. Put the drawer lid back in place. Working fine. Thanks!!
Parts Used:
-
Patricia from Fernandina Beach, FL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
A bit difficult to reach inside the refrigerator
I used the feedback information from others who commented on your website
Parts Used:
-
Edward A from St Joseph, MO
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
Ice Maker was not functioning
I followed your posted video. Did step by step as video instructed and in about 30 minutes finished. Ice was made approx 30 minutes later. I hope you do more videos, a picture is worth a thousand words.
Parts Used:
-
BRET from SAN DIEGO, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Peg broke off pantry end cap
had to remove old end cap and back piece, remove slide and replace on new part.
Parts Used:
-
Carol from Gasport, NY
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
No ice. Web site explained what to check for ..
Just followed directions.Which were clear as could be. I think it took longer to clear the freezer, than to replace the ice maker. Thanks so much.
Parts Used:
-
Stewart from Ventura, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
broken center rail ( second time)
-
GERALD from WILMINGTON, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Had to replace right end cap
Had to remove bottom drawers and glass shelf, unscrew 3 screws, the right side end cap controls the air control so there is another piece that is attached to the end cap that has to be removed from the old and put on the new cap. And do replace this part since it controls the temperature of the refriferator if not the alarm goes off.
Parts Used:
-
Cheryl from Jensen Beach, FL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The water filter indicator kept blinking red.
I opened the cover to the filter and screwed the filter counter clock wise until it came loose then removed the old filter and put the new one in. It was real easy.
Parts Used:
-
Myra from Baltimore, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Replaced ice maker
Unplugged refrigerator and truned off water supply. I then removed old ice maker by first removing screw holding mounting bracket with 1/4 inch nut driver. Then I carefully pulled up and out on the ice maker to remove it from mounting brackets on the side of unit. Once free, I was able to access the wiring harness in the back and remove it from the unit by compressing the clips and gently pulling with an even pressure. Now that the old ice maker was detached I took it to my counter and removed the on/off switch rocker bar and wiring harness. I attached these two pieces to the new ice maker. I then plugged the wiring harness back into unit and lined up the mounting brackets on the side wall and did a reverse tilt to downward pressure onto brackets until they clicked in securely. The last step was to screw in the mounting bracket with nut driver. Turned on water line and plugged machine back in. It took about an hour and a half before it produced its first harvest of ice, but has been working like a charm since.
Parts Used:
-
Christopher from Cave Creek, AZ
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Ice leaking water.
Watch the video on the sight and that was almost all I really needed. The only thing I would add is that it took me some time to get the drawer freezer door off. Lift the front straight up. Don't pull the door slides out.
Parts Used:
-
Paul from Madison, WI
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Water Filter Replacement
It was very easy, just unscrew old filter and screw in the new filter. Reset the warning light, and done. Ralph Mason, 403 Sundance Lane, Georgetown, TX 78633
Parts Used:
-
Ralph from Georgrtown, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!