KAWS750LQ0 KitchenAid Washer - Instructions

As per the video that was sent. The washer was repaired very easily and with no problems and minimum time spent. Thank you for your fantastic service and information to accomplish the repairs and look forward to doing business with you again in the future. Steve and Lory

I took out the old inlet valve and put the new one in. It was easy

Pulled off the old dispenser and popped on the new one. As easy as that. No tools needed. By the way. The service at Partselect was unbelievable. Had the part in about four days. Thanks Partselect.

used socket wrench with an 8in extension to remove agitayor bolt that was under cap on top part of agitator. was back together in about 15 min.correct parts were shipped in record time.

I searched the web and found your YouTube Repair Video... I said to myself "I can do that". I ordered the kit and it arrived in 2 days !!! I was amazed. From the video I estimated my repair time to be around 20 - 30 minutes. I was done in less than 10 minutes. I Love You! I Mean it!THANKS! Mike*

Removed and took apart agitator and replaced directional cogs.

It was my Mothers washer & did find out the Direct drive Motor Coupling was a little warn & replaced not to hard but took more time to get top off because you have to really get under the top off hood & clips where really in there the vidio showed held on with screws & on this Kenmoore Elite the Clips are under the Hood which does make it alittle bit harder so you have to be careful not to bend up the Hood where all your controls are , But did not solve the issue. Looked at lid switch & it was damaged so now going to Replace it. If this was my machine probably would be a bit easier to have seen it is the Lid switch hopefully this next part will fix the problem.

Unplugged the machine, removed the rear panel and then removed the old water inlet valves. Replaced the water valves with the new one purchased through Parts Select. Installed the back panel on the machine, plugged the machine in and reconnected both the hot and cold water hoses. Tested machine works like a new one again, problem resolved.

Because your video was done so well, it only took about 10 minutes to make the replacement. I was really impressed when my tracking notice was e-mailed it included the link to the instructional video. I will recomend your web site to others.

I was skeptical that this would take less than 15 minutes, but it actually took closer to 5 minutes! (1) Remove the fabric softener cup from the top of the auger by pulling up on the collar as indicated. (2) Pry the cap off the auger with a small screwdriver. (3) Use a long 1/2 inch socket extender (with no socket on it) to unscrew the plastic retainer for the mechanism at the top of the auger. Remove the mechanism. (4) In the mechanism, there's a thin collar holding in the agitator directional cogs. Pry that collar up to remove it. This was the trickiest part. I was afraid of breaking that collar but it survived. (5) Replace the cogs. (6) Reverse the previous steps.

Used the directions provided and used white lithium grease versus agitator grease working fine. You should really include the grease and include it in the package only concern.

Followed video instructions.

Followed website instructions, worked for a couple days, appears it needs clutch or possibly transmission(red oil present)

one thing that you do not need to do is to remove the pump from the motor, I tried to remove it as per the instructions but the pump cracked,remove both inlet and outlet hoses from the pump and remove the pump and motor together, don't try to take them apart, you don't need to, thanks

Did not know problem or how to access - thought the back came off washer. Typed in symptoms and it pretty much pinpointed the most likely cause. Watched video on how to take it apart (BTW the front and sides come off, NOT the back). Followed the guide, took motor off and sure enough one of the plastic couplers was cracked. Ordered from PartSelect and with regular shipping the cost was under $20 (ordered Tues. night, had it by Thurs.) Installed part - note as someone else said the new piece has metal inserts which make it really snug to go around the drive shaft, but the tip about using an oversized socket and some light taps to get it on worked liked a charm. Put it all back together (getting case back on was toughest part)and its been working fine for the last week - heavy & lite loads. Have to say was thinking the whole thing needed to be replaced (sound & age) but for $20 it was worth the shot...Glad i came here first!