Models > KAWS677EQ0 > Instructions

KAWS677EQ0 KitchenAid Washer - Instructions

All installation instructions for KAWS677EQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KAWS677EQ0
1,546-1,560 of 1,669
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Agitator and drum would not turn, but water would pump out

  • Customer: John from Prosperity PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Watched the video on this sight. Fallowed instructions in video and everything went very smooth.

Agitator would not move or spin

  • Customer: Donald from Orlando FL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Unplugged, removed water supply hoses, removed drain hose from washer, laid whole washer on it`s back without removing the cabinet, popped clips off the water pump and laid to side, took two screws out of clips that hold motor on and popped them off with a screw driver, unplugged wiring harness and another single wire on motor and then lifted motor off. Then pried the plastic pieces of the coupling off the the motor and transmission shaft. Cleaned debris off motor and washer, replaced plastic piece to the transmission and set rubber part on plastic. Then replaced new plastic piece on motor and set motor back into bracket and put all parts back on in reverse order. I make it sound hard but was a easy job.

Turned out to be two problems. The washer would not spin but it would drain. Secondly, it did not agitate.

  • Customer: Russ from Milton VT
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
After watching the videos on how to complete the repairs, I ordered the parts. That next weekend I watched the videos again and from start to finish I was done in just under 1 hour. The most difficult part was getting the cabinet back on. The total cost to me was less than $45. Sure beats $600 plus for a new washer. And the next time, I'll order the double action lubricant for the agitator from Part Select. Buying that at the local appliance center was costly.

Motor did not turn drum and made sound

  • Customer: AL from Marlton NJ
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Your video was very helpful in showing steps for repair so I didn't have to discover how to disassemble. The old Direct Drive Motor Coupling had three broken couplers on one side and a cracked center on the other. New Direct Drive Motor Coupling was a much improved design that should last even longer than original. The couplers metal sleeves and overall thicker part was what original should have been.

Washer would not spin

  • Customer: Laura from Ocala FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I Googled "washer would not spin" and came upon the PartSelect YouTube video on replacing the motor coupling. Since this seemed easy enough (and I'm a 40-year-old Mom), I decided to take the washer apart as the video instructed just to see if I could find anything obviously broken or out of place. Low and behold, the rubber gasket around the coupling was broken and indicated the coupling probably was too. I ordered the part through the direct link on the YouTube video and easily put the new coupling on and VOILA! The only thing I'd recommend differently is that you leave the pump alone. It doesn't need to come off to get to the coupling. After wrestling with trying to remove the pump, I left it in place, but not before unknowingly damaging it. I had some rust build-up in there and it made the fit very tight and cracked the part/sleeve the motor drive plugs into. When the washer was reassembled I found I'd caused a leak. But...no biggie. I decided to replace pump, too. Hey, now I know how to! :) Just received that part yesterday and VOILA! It's amazing what you can accomplish with the internet. Don't be afraid of this task, ladies (and gentlemen).

washer pumped water out but would not spin

  • Customer: brian from shohola PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
took the washing machine out of the washroom closet and did the repair in the kitchen

Washer wont spin

  • Customer: jason from prairieville LA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Replaced the clutch - works great. HOWEVER - check the drain pump attached to the motor, there was a small sock clogging it up which also fixed the problem. I saved 600 bucks on not buying a new washing machine!!

make noise, and slow turn the top agitator

  • Customer: joel from cary NC
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
real easy i follow your video step by step those video are great txs,.

Motor coupling broke

  • Customer: Wade from Presque Isle ME
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Once you take the housing off it's only two clips to remove the water pump from the motor, then two screws and two more clips to remove the motor itself. One issue I ran into was the new coupling was hard to put on, so the first time I did I overheated the motor because it was binding (was also very hard to get the motor back on). After taking it apart again, and slightly tapping both couplings with a hammer the motor went on very easy and washer works like a champ!

HAD A NOISE AND DRUM STOP TURNING

  • Customer: al from santa margarita CA
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
PULLED OUT WASHER I WAS GOING TO TAKE BACK OFF THEN FOUND OUT ALL PARTS ARE ON BOTTOM. LOOKED AND FOUND YOU FOLKS ON THE INTERNET SAW VIDEO ORDERED PARTS. MADE REPAIR DID 5 LOADS HEARD BANG AND IT WAS ALL OVER. THE COUPLER GAVE OUT AFTER ALL 20 YEARS . THE IS SOMETHING ELSE THAT CAUSED COUPLER TO FAIL. I WILL KEEP AT THIS REPAIR AND MAKE IT GOOD. BUT IN THE MEANTIME. I WILL PURCHASE A NEW WASHER BUT. MY WIFE WANTS HER OLD WASHER REPAIRED. SO I BETTER GET IT RIGHT. THANK YOU FOR THE QUICK DELIVERY OF PARTS I WILL GET ALL PARTS FROM YOU FOLKS.

the couplings were broken

  • Customer: oscar from Hollis NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I took apart the cover of the washing machine, remove the back, and disconnected the hoses , also disconnect the controls,remove the pump and the motor,which are ben hold by two brackets, then proceed to remove the old parts and insert the new ones, the only problem is that they fit too tight and I used a round tool to insert the new ones, after that i put everything together and bingo, the machine is working already.

Not spinning and noise

  • Customer: Dean from Belleville NJ
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
First of all I must say thanks guys for your help, the instructions were right on the money. I first replaced the clutch as per the instructions but found out that the problem was the motor coupling ........ It was broken. I ordered it, followed the instructions and I was a hero in my household. Once more thanks guys.

The washer stopped agitating but the motor can be heard running.

  • Customer: Albert from Bellflower CA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
The video installation instruction was clear and very easy to follow. However, after installing the parts and started testing the washer, the water overflowed. It looks like the water level sensor wasn't working. It caused a little flooding in the area where the washer is. I took the control panel apart once more and this time diagnosed the water level sensor and analyzed how it works. After spending almost 45 minutes with, I detached the hose attachment and blew air which caused air bubbles in the inner side of the drum. I bent the hose to hold the air while re-attaching same to the sensor. This fixed the problem and the washer is once more, operating normally. Please include this part to your video instruction. Overall, it took me 8 hours on the project including the cleanup due to overflow.

Washer made a spinning/grinding noise when it tried to agitate or spin.

  • Customer: Charleen from Aiken SC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I watched the video that PartSelect provided on their web site. The instructions were very precise and easy to follow. I watched the video twice and just followed the instructions. I would highly recommend this approach to washing machine repairs. It certainly saved me a lot of money.

A Good Fit

  • Customer: Ernest from South Windsor CT
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The most difficult part was aligning the two sides of the coupling. Disassembling the motor from the transmission was a snap. The replacement coupling was of higher quality than the original. It had metal bushings in the center holes, where they interface each driveshaft. The original did not. It was plastic.
All Instructions for the KAWS677EQ0
1,546-1,560 of 1,669