JVM2070SH001 General Electric Microwave - Instructions

I've been fixing and taking things apart since I was a kid. I hoped that it was a bad switch in the door. Got out my test meter and check the 3 different switches. All 3 tested good, but one was a bit hit and miss. It would work if the microwave was on its side and wouldn't when it was set flat. I found the switch online and installed it. Took care of the problem.It was a whole lot cheaper than buying a new microwave. Thanks! Bill Brown, Fridley, MN

replace tray

Remove two screws,slide panel to left and remove,install filter.Replace panel,and done.Service call would have cost $97,98. EH? No brainer!

Extremely easy. Less then 10 minutes tops.
Remove the screw holding the cover to the lights.
Remove the burned out bulb(s) (they may give a little resistance).
Carefully line up the holes for the prongs on the bulbs.
Insert the prongs firmly but gently using the styrofoam holders the bulb(s) was/were shipped in so as not to touch the bulb(s) with your fingers.
Replace the screw to the light cover.
Turn on the lights and give yourself a pat on the back.

Remove filter holder from bottom. Then remove fan cover from top. Then swing open panel on right side of m-wave. You can then lift control assembly to remove it and access buttom assembly

Insructions said to remove filter frame from bottom and fan cover from top,but upon looking at fan cover I could see there was only one screw above the control panel on the right. I removed the fan cover and the one screw and had easy access to detach the control panel and change the key card. Dick Rowley

This did not fix my problem. I've ordered a new microwave.

First off, UNPLUG THE MICROWAVE.

The fuse is located under the plastic grill at the top of the microwave. It's held on by two screws. Once you've removed the screws and taken off the plastic grill, you go to the right side of the microwave and remove another screw that holds a small metal grill in place. Removing the small metal grill is probably the toughest part of this repair. You kind of have to rock it back and forth a bit to get it to release. Once that's off, you can get to the fuse. I removed the burnt out one with a pair of needle nose pliers. I also put a small piece of cardboard under the fuse when I did this so I didn't accidentally drop it into the innards of the microwave. I did the same thing when I replaced the new fuse. I then plugged the appliance back in and made sure it worked. Once that was confirmed, I replaced both grills.

First, I removed the two phillips screws on the top of the microwave. Then I was able to take the venting mechanism off of the microwave. I unscrewed all of the parts attached to the broken plastic vent and reattached them to the new plastic vent. Once all the parts were on, I simply put the venting mechanism back onto the microwave and placed the two phillips screws back to hold it in place. Lastly, I reattached the springs that allow the vent to close. A simple job done in less than 15 minutes.

Upon taking the faceplate off (unplugged power source first) I found one of the wires going to the THERMO SW-TCO SENSE TEMP was completely burned away. I cut back the wire and spliced a new section with heat shrink connectors and I replaced the THERMO SW-TCO SENSE TEMP. I plugged the power back in and it works great.

The switches are not the problem! The problem is in the tolerences of the latch housing. I have ordered two new housings (Upper & Lower) and will see if the tolerences are closer. If not I will try epoxying a shim to the plate that operates the microswitches. The other option is to file the mounting slots of the housing to allow adjustment, which would be iffy,keeping them from moving with use. The exploded drawings really need to be clarified. The scale is way too small. It was extremely difficult to pick out the individual parts of the mechanisiam.

Removed upper cover. Removed screws in cover plate & motor mount. Removed inner cover with pop screw inside microwave. Reversed procees to install new motor.

Open the box.. unwraped excessive bubble wrap.. placed in microwave.. Did'nt even break a sweat..

took off upper grille and touch pad and removed the old line fuse and replaced with a new fuse ...turned on it is working fine...sources of help: UTube and GE manuel

Went to onlin source, found a couple youtube videos then went to the GE site which had a not-too-easy that find trouble shooting guide. It was extremely helpful as it described a fuse as a fix 80% of the time for touch paid failure. I really didn't believe it would b a fuse, but it was the cheapest fix, $8. I got the fuse and was surprised to fine there are two of them on this model. I took a guess and replaced the top one ( neither fuse was black or burned to indicate a failure but the top one was a bit mor greyish). put it all back together and it works fine.

I initally thought the problem was the turn table motor but after installing that motor & not being successful I realized the problem was the stirrer motor.Removing & insalling that motor was a bit more challenging but worth the effort as I saved either the cost of a repair technician or the puchase of a new one.The microwave is back in service & running fine.